User manual LA CROSSE TECHNOLOGY WS-9006U

[. . . ] To ins stall and repla the batter ace ries, please fo ollow the step below: ps 1. o E: nging batteries in any of the units, all un need to be reset by s e nits e NOTE When chan following the set up procedures. The transmit at start-up assigns a r p tter p, random secur rity a e eived and sto ored by the Te emperature S Station in the f first code and this code must be rece few minutes of pow supplied. [. . . ] OR T OUTDOO TRANSMITTER RESET BUTTON: The Temp perature Tran nsmitter has a RESET butto Use a sm pointed ob on. mall bject to gently press and y release to send a signa Follow the instructions for in SET UP regarding th display. f P he NOTE: Re emoving power from the transmitter and display nega d ates the need for the RES d SET button. POSITION NING THE TE EMPERATUR STATION: RE Stand the Temperature Station on a tabletop, counter or desk or mount on a wall. Ensu that the e e k, n ure Temperat ture Station co ontinuously re eceives the 433MHz signa from the Se al ensor before m mounting it in the desired lo ocation. WALL MOUNT Ins stall a mountin screw (not included) int a wall--lea ng t to aving approxim mately 3/16 o an of inc (5mm) exte ch ended from th wall. he Pla the Temperature Statio onto the sc ace on crew, using th hanging ho on the he ole backside. NO OTE: Always ensure that th Temperatu Station loc onto the s e he ure cks screw before rele easing the sta ation. TABLE STAND: The Temperature Station has a wide base t stand on a desk or table S e to e. POSITIONING THE REMOTE TEM R MPERATURE TRANSMITT TER: Wall mount using the hole on the back of the se b ensor. Best lo ocation is under the eave (12-18 inche on es) the North side of the ho ome. In nstall a mount ting screw (no included) in a wall--leaving approx ot nto ximately 3/16 o an of inch (5mm) exten nded from the wall. lace the temp perature trans smitter onto th screw, usin the hangin hole on the he ng ng e 2. Gently pull the trans smitter down t lock into place to NOT Always en TE: nsure that the transmitter lo ocks onto the screw before releasing. e e TABLE STAND: Not recomme N ended as the t transmitter m be blown over and may dama aged. NOTE: Th mounting surface can affect the trans he s a smission rang If, for insta ge. ance, the tran nsmitter is attached to a piece of metal, it may reduce the tr t m ransmitting ra nge. For this reason, we recommend not to place the unit on any metal surfaces or in any po m s osition where a large metall or highly pol lished surface is in e the immed diate vicinity (garage doors double-glaz ( s, zing, etc. ). [. . . ] The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your owner's manual; (5) damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference. This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. [. . . ]