User manual LA CROSSE TECHNOLOGY WS 8115U

[. . . ] 7 Daylight Saving Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Page 1 of 12 Features: WWVB Radio Controlled Clock (Atomic Clock) Time in 12/24 hour format Manual time setting option Time Zone setting: +/- 12 Hours from GMT Daylight Saving Time(DST) On/Off Continuous calendar up to year 2054 Date and weekday displayed and set Temperature display in °F or °C Snooze function (10 minutes) Indoor thermometer Wireless Outdoor Temperature Sensor Battery - Atomic Clock: 2 X "AA" size 1. 5V (not included) automatically with the time Battery - Wireless Outdoor Temperature Sensor: 2 X "AAA" size 1. 5V (not included) Page 2 of 12 Low battery icons for display and sensor Setup Information: The Temperature Sensor uses 2 x AAA, IEC LR3, 1. 5V battery. To install and replace the batteries, please follow the steps that follow: the reception is tried for 22 seconds on 910MHz. The Outdoor Temperature Sensor Position the Atomic Clock and the Outdoor Sensor five to six feet apart with nothing between them. [. . . ] The three-letter abbreviation for the day of the week will display in the bottom of the LCD while the setting flashes above. US: English (default setting) F: French (Français) E: Spanish (Español) d: German (Deutsch) Note: Manual time and date settings are optional. In most cases, the time and date will set automatically via WWVB radio signal. If placement for the display does not allow for WWVB reception due to interference, you will need to set the time and date manually. Set Time Manually - Hour: Press the "SET" button a fourth time and the Hours digits will flash. Set Time Manually - Minute: Press the "SET" button a fifth time and the Minutes digits will flash. Set Date Manually - Year: Press the "SET" button a sixth time and the Year digits will flash. Set Date Manually - Month: Press the "SET" button a seventh time and the Month digits will flash. Set Date Manually - Date: Press the "SET" button an eighth time and the Date digits will flash. Set Date Manually - Day of Week: Setup of Time and Display Options: Above: Back view of Atomic Clock showing buttons and battery compartment. The display will exit SET mode automatically after 10 seconds of inactivity. If the display exits SET mode while you are following the setup instructions, press the "SET" button the indicated number of times to return to the portion of the SET mode desired. Set the Time Zone: Press the "SET" button and the Time Zone display will flash. Use the "PLUS" button to select the correct Time Zone setting from the available selections below: -1, -2, -3: Other time zones -4: ATL - Atlantic -5: EST - Eastern (default setting) -6: CST - Central -7: MST - Mountain Page 5 of 12 Page 6 of 12 Press the "SET" button a ninth time and the Day of Week abbreviation will flash. Set 12 or 24 Hour Time Mode: Press the "SET" button a tenth time and the 12 or 24 Hour Time Mode digits will flash. Use the "PLUS" button to set the time mode to either a 12 or 24 hour clock. Set Temperature Mode - °F or °C: Press the "SET" button an eleventh time and the Temperature Mode abbreviation will flash. Use the "PLUS" button to set the temperature mode to °F or °C. About the Daily Alarms: After 30 seconds without pressing any button the clock switches automatically from alarm setting mode to normal clock mode. The alarm uses 3 different patterns of tone, beginning gently and increasing in intensity, known as a "Crescendo Alarm". The effect is to provide increasing levels of alarm to ensure waking while providing a gentle alarm to lighter sleepers. The National Institute of Standards and Technology and WWVB encode a special DST "bit" in the WWVB transmission for DST. Your La Crosse Technology® clock will read this information (only if "DST" is set to "On") and automatically advance the time one hour in the spring and back an hour in the fall. [. . . ] This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. Some States do no allow the exclusion of consequential or incidental damages; therefore the above exclusion of limitation may not apply to you. [. . . ]