User manual LA CROSSE TECHNOLOGY WS-1913 QUICK SETUP GUIDE

[. . . ] You may need to check the cable for correct connection and all the components for correct function by manually turning the wind-gauge by moving the wind-vane; tilting the rain sensor to hear the impact of the internal moving seesaw, etc. After the Weather Center has been checked for correct function with regard to the above points and found fit, the initial set up of the weather station system is finished and the mounting of the system components can take place. However that all components work properly together at their chosen mounting or standing locations. [. . . ] This is because a random security code is assigned by the transmitter and rain sensor (optional) at start-up and this code must be received and stored by the Weather Station in the first 90 seconds of power being supplied to it. Note: The stored History record will not be kept after the battery change is done on the weather station. The LCD screen is split into 3 sections displaying the following information: 1. Time and date/ indoor temp/ second Wind data, outdoor temperature and humidity, dew point, weather forecast icon and tendency indicator Air pressure history, relative air pressure, rainfall data (optional) Calendar / indoor temperature / seconds display Wind speed / gust* in mph, km/h, m/s Weather forecast Icon Low battery indicator (weather station) Outdoor relative humidity in % Low battery indicator # (transmitter) Relative air pressure / 24 hr rainfall / Total rainfall display* (only if there is a rain sensor being used) SET key + key HISTORY key MIN/MAX key SET key x Press and hold to enter manual setting modes: LCD contrast, Manual time setting, 12/24 hour time display, Calendar setting, ºC/ ºF temperature unit, Wind speed unit, Rainfall unit, Pressure unit, Relative pressure reference setting, Weather tendency threshold setting x Press to toggle between the display of Mode 1 or Mode 2: Mode1: "Wind speed + outdoor temp + rel. Pressure" Mode 2: "Gust + Dew Point temp + rainfall data (only if there is a rain sensoroptional)" (Mode 2 displayed will be shown for 30 seconds. Then it will return to normal display x Press to activate the reset mode when MAX or MIN record is shown + key In display Mode 1, press to toggle the date, weekday, + date, Indoor temp, or sec In display Mode 2, press to toggle the Relative Pressure, 24 hour rainfall and Total rainfall (if there is a rain sensor- optional). Press to adjust (increase) the level of different settings Press to confirm to reset the MIN/MAX record HISTORY key x Press to display the weather data history records or exit manual setting mode MIN/MAX key x Press to display MIN/MAX records of various weather data or adjust (decrease) the level of different settings When the signal from the transmitter/ or Rain sensor (optional) is successfully received by icon will not the Weather Station, the icon will be switched on. User can therefore easily see whether the last reception was successful ("ON" icon) or not ("OFF" icon). On the other hand, the short blinking of icon shows that a reception is being done at that time. The * In normal display user may press the SET key shortly to toggle between Mode1 and Mode 2 display: Mode 1: Wind speed, outdoor temperature, relative air pressure are shown. Using 915MHz wireless transmission gives users little restriction on placement because all units can be positioned virtually anywhere within a 330 ft / 100 meters radius of the base station. Please ensure that the cable included in this set meets your distance requirements (see accessories in the main user manual for adding extension cables). Important: Ensure all signals can be received and/or all cable distances meet with your requirements at the point of fixing particularly before you start drilling any mounting holes. Secure the main unit to the shaft of the mast holder using the single screw provided with the front of the sensor (marked E) facing in the East-West direction otherwise wind direction will not be accurate. Now fix the entire unit to a suitable mast using the U-bolt, washers and nuts found in this set. Note: For best results mount the wind sensor onto a mast to allow the wind to freely travel from all directions to enable an accurate reading (ideal mast size should be from Ø 5/8" to 11/4"). Transmitter signal reception icon In Mode 1, this reception icon is showing the condition of the reception of the signal from Thermo-hygro transmitter To wall mount the thermo-hygro sensor, fix the wall holder onto the desired wall (2 screws are supplied), plug the sensor firmly into the wall holder and then carefully replace the rain cover back over the thermo-hygro sensor. Note: After mounting the units, should the weather data not be received, user may need to remove the batteries from all units and redo the set-up procedures after about 5 minutes. [. . . ] La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your owner's manual; (5) damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference. This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. [. . . ]