User manual LA CROSS TECHNOLOGY WT-5600

[. . . ] This number will connect you to an automated time, announced at the top of the minute in "Coordinated Universal Time", which is also known as Greenwich Mean Time (GMT). It is possible that your Projection Alarm may not be exactly on the second due to the variance in the quartz. However, the clock will adjust the quartz timing over the course of several days to be very accurate; under . 10 seconds per day. 3 QUICK SET-UP GUIDE 1) Insert two AA batteries into the Projection alarm and/or plug into wall 2) Wait 10 minutes for WWVB reception. 3) If there is no WWVB reception, manually set the time and date (instructions in the Program Mode). [. . . ] Hold down the "MODE/+" button for 2 seconds (the selected time zone will flash), press the "AL" button three times until the year flashes. Press the "AL" button to confirm the year and move to the month setting. Press the "AL" button to confirm the month and move to the day setting. Press the "AL" button to confirm the day and move to the 12/24 Hour display setting, or press the "SNOOZE" button to confirm the date and return to the display mode. F. Hold down the "MODE/+" button for 2 seconds (the selected time zone will flash), press the "AL" button six times until " :12" flashes in the time display. Press the "MODE/+" button to toggle between 12 and 24-hour time display. Press the "AL" button to confirm the time display setting and move to the Daylight Saving Time setting, or press the "SNOOZE" button to confirm the time display setting and return to the display mode. 2. DAYLIGHT SAVINGS TIME Note: The DST default is "On", meaning that the WWVB will automatically change the time according to Daylight Saving Time in the spring and fall. For areas that do not recognize DST changes (Arizona and parts of Indiana) turn the DST to "OFF". Hold down the "MODE/+" button for 2 seconds (the selected time zone will flash), press the "AL" button seven times until "ON" flashes in the date display area and "DST" flashes above the U. S. Press the "MODE/+" button to toggle between "ON" and "OFF" modes. Press the "AL" button to confirm the DST setting and complete the set-up. Radio-controlled time and date Projection of time LCD light Three modes of date/seconds display Time alarm 8 B. The projection alarm will automatically search for the time signal upon initial set-up and every night. When the signal is being received, there will be a "tower" icon flashing to the right of the time display. When the time signal has been received successfully, the tower icon will remain steady until midnight. The NIST (National Institute of Standards and Technology--Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously throughout the United States at 60 kHz. The signal can be received up to 2, 000 miles away through the internal antenna in the Projection Alarm. Due to the nature of the Earth's Ionosphere, reception is very limited during daylight hours. The Projection alarm will search for a signal every night when reception is best. The WWVB radio station receives the time data from the NIST Atomic clock in Boulder, Colorado. [. . . ] The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow instructions contained in your owner's manual; (5) damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and uses that this product was not intended or (8) the products inability to receive a signal due to any source of interference. . This warranty covers only actual defects within the product itself, and does not cover the cost of installation or removal from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the seller or performance variations resulting from installation-related circumstances. [. . . ]