User manual KYOSHO ULTIMA RACING SPORTS GP EXPLODED VIEW

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer . While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information Oki is a trademark of Oki Electric Industry Company Ltd. Apple, Macintosh and Mac OS are registered trademarks of Apple Computers Inc. [. . . ] Locate the metal Outside Media Guide (1) under the print path and slide it toward you as far as it will go. LE810DT User's Guide 22 6. Push in on the bottom of the Outside Media Guide (1) to move the top out of the way while you are loading the media. 7. Slide the media into the print path, making sure it goes under the Media Hold-Down (1) and under the Sensor Assembly (2) Push it against the back of the printer. If the media does not go under the Sensor Assembly, the printer will not recognize that media is loaded. LE810DT User's Guide 23 8. Adjust the media sensor to compensate for irregularities in the media (i. e. : notch, tag hole, gap, perforation or markings). To properly adjust the sensor position, loosen the green Sensor Adjust Knob located on the bottom side of the Media Transport Assembly and move the sensor in ¼ inch increments (or finer) until the sensor error is cleared. After the error is cleared, retighten the green Sensor Adjust Knob. 9. Pull out the bottom of the Outside Media Guide so that it is upright, then push the guide inward until it barely contacts the outside edge of the media. LE810DT User's Guide 24 10. Swing the Head Latch back down to close the print head, then latch it in place. 11. Close the front door and lower the top access cover into place. b Attention!These covers have interlock switches and the printer will not operate if either is open. LE810DT User's Guide 25 Fanfold Type 1. Lift up the Top Access Cover. LE810DT User's Guide 26 If the back plate is on your printer, perform the following step; other wise, skip to step 3. Press on the pin holders (1) inside the printer at either end of the bracket until the pins extend from the outer housing. b Carefully pull out the pins at either end of the cover plate and save them. The label pitch is the distance from the leading edge (the edge that comes out of the printer first) of a label and the leading edge of the next label. Once the position has been set, it can be fine adjusted using the PITCH potentiometer. Positive (+) digit settings moves the leading edge forward and away from the print head while a negative (-) setting moves the label's leading edge incrementally back into the mechanism. If YES is selected, the print data will be deleted and then the printer will go offline. If the NO option is selected, the printer will go offline without deleting data in buffer. Provides the specific sequence of events required by the operator, the printer, and the printer's software for a test label to be printed. Select YES to enter User Test Print menu while select NO will advance to Online mode. OFFLINE QTY XXXXXX PRINT DARKNESS 12345 PRINT SPEED 23456 PITCH OFFSET +00MM CANCEL PRINT JOB YES NO USER TEST PRINT YES NO LE810DT User's Guide 39 Printer Configuration Advanced Mode Display ADVANCED MODE Description Is the first menu screen of the Advanced Mode. The Advanced Mode is provided to make basic printer operational adjustments. Typically, once these adjustments or settings have been made, they will not require additional address unless a new job is downloaded. The printer can be set to automatically go into the online mode when powered on. Otherwise, theprinter starts in the offline state and must be manually placed online before it is ready to print. [. . . ] Select YES to enter User Test Print menu while select NO will advance to Online mode. The ONLINE status is displayed on the top line and the label quantity status is on the bottom. Ready for print job. USER TEST PRINT YES NO ONLINE MODE (Z) QTY: XXXXXX LE810DT User's Guide 42 Printer Configuration Default Setting Mode Display DEFAULT SETTING YES NO Description Is the first menu screen of the printer's Default Setting Mode. The Default Setting Mode allows the printer to be reset to the programmed condition as received from the factory. [. . . ]