User manual KYOSHO PITTS SPECIAL 40 PARTS LIST

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Microline are registered trademarks of Oki Electric Industry Company Ltd. Apple, Macintosh and Mac OS are registered trademarks of Apple Computers Inc. ENERGY STAR is a trademark of the United States Environmental Protection Agency. [. . . ] Manual Gap Settings Setting Manual Gap 1 Used for · Single sheets 14 to 22 lb. US Bond (52 to 81 g/m2) · Thickness range 0. 06 to 0. 10 mm · Single sheets 22 to 34 lb. US Bond (81 to 128 g/m2) · 2-Part Multi-Part Forms (carbon-backed) · Thickness range0. 10 to 0. 15 mm · Single sheets 34 to 42 lb. US Bond (128 to 156 g/m2) · 3-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 15 to 0. 20 mm · Postcards · 4-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 20 to 0. 25 mm · 5-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 25 to 0. 30 mm · 6-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 30 to 0. 35 mm · 7-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 35 to 0. 40 mm · 8-Part Multi-Part Forms (carbon-backed) · Thickness range 0. 40 to0. 45 mm · Heavy paper, 0. 45 to 0. 50 mm thick · Heavy paper, 0. 50 to 0. 55 mm thick · Heavy paper, 0. 55 to 0. 60 mm thick · Heavy paper, 0. 60 to 0. 65 mm thick · Heavy paper, 0. 65 to 0. 70 mm thick Manual Gap 2 Manual Gap 3 Manual Gap 4 Manual Gap 5 Manual Gap 6 Manual Gap 7 Manual Gap 8 Manual Gap A Manual Gap B Manual Gap C Manual Gap D Manual Gap E Microline 8810 User's Guide 57 Gap Pos. When Auto Gap detection is enabled, this sets how far in from the left edge of the form the gap detection begins: 2 inches (51 mm) [the default] or 4 inches (102 mm). Graphics The default is Bi-directional. Changing to Uni-directional will improve the print registration, but slow the print speed. Graphics Data Sets graphics data to print 7 Bits [the default] or 8 Bits. High Skip The default is Yes. This enables the low-vibration mode, which reduces printer vibration during printing. To switch low-vibration mode off, change this setting to No. Host Interface Choose the interface mode: Auto Interface [the default], Parallel, USB, or Option I/F. I-Prime The default is Enable: print out the buffer contents when the I-Prime signal is received. Change to Disable if you wish the printer to ignore the I-Prime signal. I/F Time Out Appears only if Host Interface is set to Auto Interface [the default]. Choose the amount of time the printer waits (while receiving data) before going into idle mode: 15 sec [the default], 30 sec, 45 sec, 1 min, 2 min, 3 min, 4 min, or 5 min. If your software spends a long time processing between portions of data it feeds to the printer, choose a longer time interval value to keep your printer from dumping the received data while it is waiting for more. Impact Mode Selects the print mode, Normal [the default] or Quiet, engaged on power up. Microline 8810 User's Guide 58 Initial Pos. Choose where continuous form paper will be positioned when the printer is turned on. Tear: the paper is at the tear-off position. Language Set Replaces certain standard symbols with special characters used in foreign languages. [Paper End Position] This sets when the the printer will move to the next continuous form, based on the distance between the center of the characters on the last line of the form and the bottom of the form. Available settings: 3. 18 mm (1/8") or 6. 35 mm (1/4") [the default]. Microline 8810 User's Guide 62 Pitch Choose the character width, in characters per inch (cpi): 10 [the default], 12, 15, 17. 1, or 20 cpi. Power Save Time Sets the time the printer waits before entering the Power Save Mode when Power Saving is set to Enable [the default]: 5 min, 10 min [the default], 15 min, 30 min, or 60 min. Power Saving Sets whether or not the printer enters the energy-saving Power Save Mode after the interval specified under Power Save Time. Change he setting to Yes if you want to print the DEL code (decimal 127) as a solid box. Print Dir. Cmd. The default is Valid: the printer will recognize a command for unidirectional printing. Change to Invalid if you do not wish the printer to recognize uni-directional printing commands. Print Mode Choose the print quality and speed: Utility [the default], NLQ Courier, NLQ Gothic, or DRAFT. Print Suppress The default is No. If your system uses the DC1 and DC3 codes for print suppress mode, change the setting to Yes. Prop. Choose Yes to engage proportional spacing of characters. Protocol Applies only when the optional RS-232C Serial Interface is installed. Microline 8810 User's Guide 63 Sets the protocol used: Ready/Busy [the default] or X-ON/X-OFF. Rcv. Buffer Sets the amount of memory ( 0 or 128 Kbytes) devoted to holding received data. Changing this to 0 will tie up your computer while printing, but if you abort the print job, the printer will stop much sooner. Rear Load Adj. Applies only when the optional Rear Push Tractor is installed. For fine tuning the Top of Form (TOF) location when using continuous forms with the rear push tractor. Negative values decrease the space down from the top of the form: · TOF moves up. [. . . ] Direct Network Printing Utility (LPR) The Direct Network Printing Utility (LPR) allows you to print directly to a printer on the network without a print server. It creates a Printer Port, and installs a pop-up status box so you can monitor printer status. The Direct Network Printing Utility (LPR) operates in Windows Me/98, Windows NT 4. 0, Windows 2000, and Windows XP operating systems. KYOSHO DIPUS (Dot Impact Printer Utilities) This is a set of utilities that allow you to control the printer from your computer. [. . . ]