User manual KYOSHO PIPER J3 CUB 40 PARTS_LIST

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Microline are registered trademarks of Oki Electric Industry Company Ltd. Apple, Macintosh and Mac OS are registered trademarks of Apple Computers Inc. ENERGY STAR is a trademark of the United States Environmental Protection Agency. [. . . ] This enables the low-vibration mode, which reduces printer vibration during printing. To switch low-vibration mode off, change this setting to No. Hi-Impact Copy The default is Invalid. Change the setting to Valid if you wish the printer to automatically start up in the Hi-Impact mode when it is turned on. The Valid setting will not engage the Hi-Impact mode when the I-Prime (parallel) or Soft_Reset (USB) commands are received. Host Interface Choose the interface mode: Auto Interface [the default], Parallel, or USB. I-Prime The default is Enable: print out the buffer contents when the I-Prime signal is received. Change to Disable if you wish the printer to ignore the I-Prime signal. I/F Time Out Appears only if Host Interface is set to Auto Interface [the default]. Choose the amount of time the printer waits (while receiving data) before going into idle mode: 15 sec [the default], 30 sec, 45 sec, 1 min, 2 min, 3 min, 4 min, or 5 min. If your software spends a long time processing between portions of data it feeds to the printer, choose a longer time interval value to keep your printer from dumping the received data while it is waiting for more. Microline 8480FB User's Guide · 46 Initial Pos. Choose where continuous form paper will be positioned when the printer is turned on. Tear: the paper is at the tear-off position. Language Set Replaces certain standard symbols with special characters used in foreign languages. Choose American [the default], French, German, British, Danish 1, Swedish, Italian, Spanish I, Japanese, Norwegian, Danish II, Spanish II, Latin American, French Canadian, Dutch, or Publisher. Line Spacing The default is 6 LPI (lines per inch). Change to 8 LPI to get more lines on a page. LF Revise (Cut) Adjust the line feed value for manual feed using the platform. The default setting is 0. Load LF Speed Choose the paper feed speed for inserting sheets when you are using manual feed from the platform: Fast Speed [the default] or Slow Speed. Memory Auto Align The default is Valid. Change this to Yes to prevent your software from resetting your printer's settings. The printer will ignore an INITIAL command. Set Alarm Controls the Paper Set Alarm. Change to Invalid if the Paper Set Alarm sounds when you try to load preprinted forms with anomalies at the top, such as a large dark area or a cutout. These types of forms defeat the paper sensors. SI Pitch (10) IBM emulation only. Sets the pitch to be engaged when the printer control panel is set for 10 cpi and the SI command is received. Choose 15 cpi or 17. 1 cpi [the default]. SI Pitch (12) IBM emulation only. Sets the pitch to be engaged when the printer control panel is set for 12 cpi and the SI command is received. Choose 12 cpi or 20 cpi [the default]. Size The default is Single. Choose Double for double width and height printing. Skew Detect Detects and corrects paper skew when manual feed through the platform is being used with Auto Align disabled. Available settings: Valid Level 1, Valid Level 2 [the default], or Invalid. Change to Invalid if you are experiencing difficulty getting forms to load into the printer when using preprinted forms with anomalies Microline 8480FB User's Guide · 51 at the top such as a large dark area on one side or a cutout. [. . . ] Note If you are consistently using recycled paper, you need to clean the housing more often because recycled paper generates more paper dust. Caution! Never use solvents or strong detergents on the cabinet: they could damage the housing. Open the platform and use a clean, dry cloth to clean away any bits of paper and paper dust. F5-03b. JPG 3. Tilt the display panel forward and remove the ribbon cartridge. F2_18a. JPG 6. Use a clean, dry cloth to clean any bits of paper or paper dust from around the platen. Microline 8480FB User's Guide Maintenance · 81 7. [. . . ]