User manual KYOSHO PERFEX KT-5

[. . . ] Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association. Ownership of all other trademarks is attributed to their due owner. An administration fee may be charged if either (a) an engineer is called out at your request and there is no defect in the product (i. e. (b) you bring the unit to a repair centre and there is no defect in the product (i. e. [. . . ] Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled in the middle. 2 Click the Add button. The Add Schedule window will appear. 3 Using MDC 90 3 3 Using MDC Click Add below the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list window. Action: Select a function that will activate at the specified time and interval. Schedule Modification To modify a schedule, select the schedule and click Edit. Deleting a Schedule To delete a schedule, select the schedule and click Delete. 3 Using MDC 91 3 Using MDC 3. 4. 14 Troubleshooting Guide Issue The display you want to control does not appear on the system information chart. Solution Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). Connecting displays with a duplicate ID can cause the displays not to be shown due to data collision. (Change the ID using the Display menu. ) For a display that supports the ID in a range of 0 to 99, the ID should be set between 0 and 99. 3. The display you want to control does not appear on the other Control Info Grids. The following message appears repeatedly. Check that the display is powered on. (See the power status in the system information chart. ) Ensure you select the input source the display is connected to. The change will be applied. 4 Screen Adjustment 97 4 Screen Adjustment If the input source is AV, Component or TV: Custom Contrast Brightness Sharpness Color Tint 100 45 50 50 G r e e n 50 R e d 50 Move Enter Return Contrast Adjust the contrast between the objects and background. (Range: 0~100) A higher value will increase the contrast to make the object appear clearer. (Range: 0~100) A higher value will make the outline of objects clearer. (Range: 0~100) Increasing the red level will make the red color more prominent in the picture. Increasing the green level will make the green color more prominent in the picture. 1 Press / to move to the option you want and press [ ]. A window will appear where you can adjust the value for the selected option. Contrast Move Adjust 100 Return 2 Press / to adjust the value and press [ ]. The change will be applied. 4 Screen Adjustment 98 4 4. 3 Screen Adjustment Color Tone Adjust the general color tone of the picture. This function is available when Dynamic Contrast is set to Off. (Refer to page 111 for details about Dynamic Contrast) Changing any setting under Color Tone will change the Mode setting to Custom. 4. 3. 1 Configuring the Color Tone Settings This product can only be controlled by using the remote control. 1 2 3 Press MENU on the remote control. ]. to move to Color Tone and press [ Different Color Tone options are displayed depending on the current input source: If the input source is PC or DVI: Color Tone Off Cool Normal Warm Custom Move Enter Return 1 Press / to move to the option you want and press [ ]. The selected option will be applied. If the input source is AV, Component or TV: Color Tone Off Cool2 Cool1 Normal Warm1 Warm2 Move Enter Return 1 Press / to move to the option you want and press [ ]. The selected option will be applied. 4 Screen Adjustment 99 4 4. 4 Screen Adjustment Color Control Change the color settings for the picture by adjusting the Red, Green and Blue values. (Range: 0~100) A higher value will increase the intensity of the selected color. This option is available when the input source is PC or DVI. (Refer to page 99 and page 111 for details about Color Tone and Dynamic Contrast. ) 4. 4. 1 Configuring the Color Control Settings This product can only be controlled by using the remote control. 1 2 3 Press MENU on the remote control. [. . . ] Regular Color Change Type 1 Type 2 FLIGHT OZ348 UA102 Use 2 colors TIME 20:30 21:10 FLIGHT OZ348 UA102 TIME 20:30 21:10 Switch between 2 colors every 30 minutes as shown above. Avoid combinations of a text color and background color of contrasting brightness. Avoid using colors of contrasting brightness (black and white; grey). FLIGHT : TIME OZ348 : 20:30 Regular Text Color Change FLIGHT : TIME OZ348 : 20:30 Use bright colors of similar brightness. Interval: Change text color and background color every 30 minutes FLIGHT : TIME OZ348 : 20:30 FLIGHT : TIME OZ348 : 20:30 FLIGHT : TIME OZ348 : 20:30 FLIGHT : TIME OZ348 : 20:30 Move and change text every 30 minutes as shown below. FLIGHT OZ348 : TIME : 20:30 FLIGHT OZ348 : TIME : 20:30 [ Step 1 ] [ Step 2 ] [ Step 3 ] Regularly display a moving image along with a logo. Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours. Appendix 165 Appendix The best way to protect the monitor from afterimage burn-in is switching the power off or setting the PC or system to run a screen saver when not in use. [. . . ]