User manual KYOSHO MINI-Z MONSTER BALL BEARING SET

[. . . ] While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the Oki web site: http://my. okidata. com Copyright © 2005 Oki Data Americas, Inc. This publication is protected by copyright, and all rights are reserved. No part of it may be reproduced or transmitted in any form or by any means for any purpose without express prior written consent from Electronics for Imaging, Inc. [. . . ] If the solid density patches (100% cyan, magenta, yellow, or black) look less saturated with time, show the pages to your printer service technician to determine whether adjusting the printer can improve output. Checking calibration status To verify whether the Fiery is calibrated, which calibration set and ES3640e MFP Color Guide - 42 2 2-43 Understanding calibration output profile were used, and when the printer was last calibrated: · Print a Configuration page or Test Page from the Control Panel or Command WorkStation/Command WorkStation LE. · Select a calibration set in Calibrator (available from ColorWise Pro Tools); the last calibration and the user who performed it are displayed. ES3640e MFP Color Guide - 43 2 2-44 Color Calibration Using Calibrator ColorWise Pro Tools Calibrator allows you to calibrate the Fiery using the measurement method of your choice. Changing the calibration has the potential to affect all jobs for all users, so consider limiting the number of people authorized to perform calibration. Set an Administrator password to control access to calibration (see "Setting Passwords" in the Configuration Guide Chapter 7). Note: Multiple users can be connected to one Fiery with ColorWise Pro Tools, but only one user at a time can use Calibrator. An error message appears if you try to calibrate when another user is using ColorWise Pro Tools to calibrate. Starting Calibrator Start Calibrator from the ColorWise Pro Tools main window. Start ColorWise Pro Tools and connect to the Fiery. For instructions on configuring the connection to the Fiery, see the User Software Installation Guide. Note: If the connection to the Fiery from Command WorkStation/Command WorkStation LE (which also allows for access to ColorWise Pro Tools) is not established, you can start ColorWise Pro Tools independently of Command WorkStation/Command WorkStation LE. Click Calibrator. The Calibration window appears in Standard mode. 3. Use the Calibrator window to perform the calibration method of your choice. Procedures for each calibration method are described in subsequent sections of this chapter. ES3640e MFP Color Guide - 45 2 · 2-46 Color Calibration Expert Mode Calibrator provides two modes: Standard Mode and Expert Mode. You can perform all essential calibration tasks while in Standard Mode. Expert Mode offers two additional options: Print Pages and View Measurements. To Use Expert Mode Move the sliding button at the top of the Calibration window from Standard to Expert. The Expert Mode window appears. With the Print Pages option, print a calibration Comparison Page showing the results of the new measurements with any profile associated with the currently selected calibration set. You can also create a custom comparison page and save it as a PostScript or Encapsulated PostScript (EPS) file called CALIB. PS. Directions for measuring the strips appear in the Status field. Note: For a more accurate measurement, place several sheets of plain white paper beneath the Measurement Page to block underlying colors from being read by the instrument. 10. Place the sample aperture in the white space at the start of the specified color. Note: To hear a beep with a Windows compatible computer, you must have a sound card and speaker(s) installed. 12. After you hear a beep, slide the ES-1000 at a slow but consistent pace across the strip. Release the button when all the patches in the strip have been measured, and you have reached the white space at the end of the strip. When a strip is measured successfully, the cross hair moves to the next color. 14. Repeat step 10 through step 13 until all the strips have been measured. Note: You must take the measurements in the order outlined in the Status field. 15. When all the patches have been read successfully, click Accept. ES3640e MFP Color Guide - 52 2 2-53 Using the EFI Densitometer ED-100 16. Click Apply in the Calibrator window to implement the new calibration measurement. Click OK in the Information dialog box. This completes the Fiery calibration process. Using the EFI Densitometer ED-100 The EFI Densitometer ED-100 is a hand-held instrument that measures the density of printed ink and toner. Like the DTP32, the ED-100 is a reflection densitometer that you can use to calibrate the Fiery. Setting up the ED-100 To use the ED-100 for calibration purposes, you must first set it up for use with your computer. [. . . ] After calibrating the DTP41, calibrate the Fiery (see page 2-57). ES3640e MFP Color Guide - 104 A A-105 Color Measurement Instruments Using the X-Rite DTP32 densitometer ColorWise Pro Tools are designed to work with the X-Rite DTP32 reflection densitometer, which feeds color measurements to the Fiery automatically. Note: Measurements from other densitometers can be input using a simple ASCII file format (see Appendix B). Setting up the DTP32 Before you calibrate the Fiery using the X-Rite DTP32, you need to connect, configure, and calibrate the densitometer to prepare for measuring the printed patches (see "Calibrating the DTP32" on page A-107). For additional information about setting up and using the DTP32, see the separate documentation included with the densitometer. Plug the square end of the interface cable (looks like a modular phone plug) into the I/O port on the side of the X-Rite DTP32. Square connector ES3640e MFP Color Guide - 105 A A-106 Unused connector Connect to computer Connect to adapter Color Measurement Instruments 3. Attach the connector to the computer. For a Windows computer, insert the 8-pin mini-DIN end of the interface cable into the 9-pin DB9 Connector cable adapter. [. . . ]