User manual KYOSHO KELLY 70 EP

[. . . ] Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. [PC] !' [ DVI] !' [ [ DisplayPort] !' [ Note · The RGB/COMPONENT IN port is compatible with RGB (PC) and Component signals. AV] !' [ Component] !' [ MagicInfo] !' [ TV] HDMI1] !' [ HDMI2] !' Introduction However, the picture may display abnormally if the connected external input signal is different from the selected video signal. · · A TV tuner box (sold separately) must be connected to use the TV. [. . . ] For exact instructions, see the User Manual supplied with the locking device. You can purchase the locking device from an electronics store, an online shop, or our service center. · Connecting a Network Box (sold separately) PC OUT MagicInfo video output port MAGICINFO OUT This is the output terminal for the video, audio, and control signals of MagicInfo. It can be used by connecting it to the [HDMI IN 2 (MAGICINFO)] terminal using an HDMI cable. LAN (LAN Connection Terminal) Connects to a LAN cable to allow Internet or network access in MagicInfo mode. Connecting a Network Box (sold separately) USB (USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. RS232C (RS232C serial port) Serial port Connecting a Network Box (sold separately) Introduction POWER Connect the [POWER] terminal of the product and the [POWER] terminal of the monitor using a power extension cable. POWER S/W ON [ I ] / OFF Turns the network box on or off. Note The power switches of both of the monitor and the network box must be turned on for the network box to operate normally. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. POWER OFF Number Buttons DEL + VOL SOURCE D. MENU TOOLS Up-Down Left-Right buttons INFO The Color button and the PC/DVI/HDMI/ DP selection button TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV / GUIDE button Introduction MENU RETURN EXIT MagicInfo POWER OFF Number Buttons Turns the product On/Off. Used to enter the password during the OSD adjustment or to use MagicInfo. DEL / GUIDE button The "-" button is used to select Digital channels. Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time. - This button can only be used in TV mode while a TV tuner box (sold separately) is connected. Connect a video cable to [AV IN] on the product and the video output port on the external device. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the DVD player. Note · · · · Press SOURCE on the product or remote control and select "Component". For an explanation of Component video, consult your DVD manual. Connecting a DTV Set Top (Cable/Satellite) Box Connections Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the Set Top Box. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note · · Press SOURCE on the product or remote control and select "Component". For an explanation of Component video, see your Set Top Box owner's manual. Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO OUT] on LCD Display. Connecting a Network Box (sold separately) Note · · Network boxes are sold separately. For more information on how to purchase and install a network box, contact Samsung Electronics. Connections Connecting the Power Connect the [POWER] terminal of the product and the [POWER] terminal of the installed network box using a power extension cable. Connect the power cord to [POWER] on the network box and mains socket. Turn on the power switch. Connecting to MAGICINFO OUT 1. Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the HDMI cable. Connections Connecting a LAN Cable 1. Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC. Connecting a USB devices 1. You can connect USB devices such as a mouse or keyboard. Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. The figure shown below ("No Signal") appears on a black background when the LCD Display is working normally even though no video signal is detected: While in the SelfTest mode, the LED power indicator remains green and the figure moves around on the screen. 4. Turn off your LCD Display and reconnect the video cable; then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure, check your video controller and computer system; your LCD Display is functioning properly. Warning Messages You can even view the screen at a resolution of 1920 x 1080. [. . . ] Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: A: "No Signal" message. Ensure that the signal cable is firmly connected to the PC or video sources. (Refer to the Connecting a Computer) A: Q: A: A: Q: A: Ensure that the PC or video sources are turned on. [. . . ]