User manual KYOSHO INFERNO MP-7.5 SPORTS 4

[. . . ] Note This is available when a TV tuner box is installed. SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [PC] [DVI] [AV] [HDMI] [MagicInfo] [TV] Introduction Note · · The TV menu is available when a TV tuner box is installed. DR-S model can use MagicInfo menu when mounted Network box. ENTER button [ENTER] Activates a highlighted menu item. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. [. . . ] KYOSHO Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. The product may not stay in place when installed on plaster or wood. Components Only use the components and accessories shipped with the product. Introduction Wall Bracket(1) Hinge(Left 1, Right Plastic Screw 1) Hanger (A)(11) (4) Screw (B)(4) Anchor (11) Wall Bracket Assembly Note There are two hinges(left and right). When done, mount the wall bracket on the wall. There are two hinges(left and right). Captive Screw Wall Bracket Hinge (Left) Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. Introduction A3. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model. Remove the 4 screws on the back of the product. Introduction 2. Insert the screw B into the plastic hanger. Notice · · · 3. Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. Be careful when installing the product on the bracket as fingers can be caught in the holes. Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product. 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. Introduction ABC- LCD Display Wall Bracket Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. In this case, first check the source of the problem, and then contact a Service Center or your dealer. Check if the power cord and the video cables are properly connected to the computer. (If it does, request an a service for the main board of the computer. ) 3. If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video). Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel -> System -> Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver. Check List Note · The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. For more network-related information, refer to the MagicInfo Troubleshooting section. · Problems related to the Installation (PC Mode) Note Problems related to the LCD Display installation and their solutions are listed. Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Troubleshooting Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. [. . . ] (Refer to the Brightness, Contrast) Q: A: Q: The screen color is inconsistent. The color image is distorted by dark shadows. Q: A: Q: A: Troubleshooting A: Q: A: Q: A: Q: A: A: Q: A: Adjust color using Custom under OSD Color Adjustment menu. The LCD Display is currently saving the changes made in the settings to the OSD memory. The screen is blank and the power indicator light blinks every 0. 5 or 1 seconds. [. . . ]