User manual KYOSHO FORD MUSTANG GT-R CONCEPT

[. . . ] Written and produced by the Oki Data Training & Publications Department. Please address any comments on this publication by mail to: Training & Publications Dept. Laurel, NJ 08054-4620 or by email to: pubs@okidata. com For the latest product information, printer drivers, manuals, special offers, etc. , we welcome you to visit our multilingual web site: http://www. okidata. com Year 2000 Compliance All products currently sold by Oki Data are Year 2000 compliant. Each product contains information technology that accurately processes date and time data between the years 1999 and 2000, and carries no issue for the September 9, 1999 (9999) programming concern. [. . . ] to adjust the speed and NO 10 The display shows G3 ECHO Protection [ON]. change the setting and 11 Press the START key to finish programming the One-Touch key. Note: When programming a telephone number, the ID and communication parameters are unnecessary. Dial Directories 37 Programming Groups Once you have programmed some One-Touch keys or Auto Dial numbers, you can program groups to allow you to send the same fax to multiple locations. You can program up to 5 groups each containing up to 110 numbers into your MFP machine. 1 Press the SELECT FUNCTION key. 4 Using the numeric keypad, enter the group number (1-5) you want to program. 5 The display shows the number of your current group and SELECT LOC. (S). You can now add a location to your group (or delete a location from it). Refer to the instructions below. To Do This Add a One-Touch location Add an Auto Dial location Delete a previously added One-Touch location Delete an Auto Dial location Search for a location by name to add or delete Use Press the One-Touch key. If the location is in the group, press START to delete it. 6 After you have completed your selection (by pressing START key, YES or NO , the display shows SELECT LOC. Each group can contain up to a maximum of all of the One-Touch and Auto Dial locations available on your MFP machine. 7 When you are finished programming your group, press The display shows LOCATION PROGRAMMING. NO . 8 To program another group, go back to Step 3. If a person answers the phone, ask them to press the START key on their fax machine. 3 If necessary, press the START key to begin the transmission. Refer to the table below to understand some of the messages you may see during a typical fax transmission. Message (location) Explanation The remote location's Personal ID, TSI/CSI, Location ID or the telephone number you entered identifies the location during transmission. If you see this or another error message, a problem occurred during the communication. Refer to the chapter on Problem Solving for assistance. CALLING SENDING RESULT = OK COMMUN. ERROR Basic Operations 41 Search Key Dialing If you are not sure which One-Touch key or Auto Dial number contains the location you want to communicate with, use the SEARCH key to look through an alphabetical list of all of the Location IDs programmed into your MFP machine. 1 When selecting locations, press the SEARCH key. 2 Repeatedly press the SEARCH key to look through the entire list of locations in alphabetical order, or locate the letter you want on the numeric keypad, and press that key repeatedly to look through Location IDs beginning with that letter. Real-Time Dialing Normally, your MFP machine dials the entire number of the location you have selected at one time. Occasionally, it may be necessary to dial numbers in real time (one digit at a time). If your MFP machine is equipped with a handset, you can dial in real time by picking up the handset. Redialing If the line is busy or if there is no answer, your MFP machine waits, and then automatically redials the number. If your MFP machine is transmitting from memory and a communication error occurs, it automatically redials the number and tries to send the fax again. You can redial a number manually at any time by pressing the REDIAL key. [. . . ] If this problem happens often, consult your service representative. 104 KYOSHOFORD MUSTANG GT-R CONCEPT User's Guide Display Panel Messages This section lists the status and error messages that may appear on your machine's display panel, and explains what they mean and how to correct any problem they indicate. Normal Display 02:13 :FAX Under the normal operating condition, the top line of the display shows the time and the answering mode - FAX, TEL, PC, T/F, TAD or MEM. Error Messages 14:14 :FAX COVER OPEN Cover open: The upper cover is not closed. Press down firmly on the cover to make sure it is closed and latched. PAPER OUT/JAM :FAX CONFIRM AND "STOP" No Paper or Paper Input Jam: The paper tray is out of paper. [. . . ]