User manual KYOSHO EVOLVA 2005 WC PARTS LIST

[. . . ] Revised edition, 2001 Written and produced by the Oki Data Training and Publications Department. Contact Information Please address any comments on this publication to: Mailing Address Oki Data Americas, Inc. Laurel, NJ 08054-4620 e-Mail Address pubs@okidata. com Web Site Please visit Oki Data's multilingual web site at: http://www. okidata. com Trademark Information KYOSHO and MICROLINE are registered trademarks of Oki Electric Industry Company, Ltd. Energy Star is a registered trademark of the United States Environmental Protection Agency Epson is a registered trademark of Epson America, Inc. IBM is a registered trademark of International Business Machines Corp. [. . . ] Paper remains in the tear-off position until the printer receives more data. Then, the paper moves back down for printing (retracts to the initial print position). If the software package you are using "pauses" while sending data to the printer, Forms Tear-Off may be activated (if it is enabled through the Menu). Forms Tear-Off CANNOT be used when the optional pull tractor is engaged. 48 | Microline 390/391 Turbo Changing the Forms Tear-Off Setting The default setting for Forms Tear-Off is OFF. 1 SEL SEL MENU SHIFT LF Micro Feed Down 2 32T-FP. eps 3 4 5 FF/LOAD Micro Feed Up TEAR PARK QUIET TOF !! The status of the Forms Tear-Off menu setting affects how you set the Top of Form. If the software package you are using "pauses" while sending data to the printer, Forms Tear-Off may be activated (if it is enabled through the Menu). Forms Tear-Off CANNOT be used when the optional pull tractor is engaged. EXIT POWER GROUP ALARM ITEM MENU SET PRINT To change the Forms Tear-Off setting: 1 Press SHIFT (2) + SEL (1). 2 Press GROUP (3) until one of the following lines appears, depending on which paper feed you are using REAR FEED Form Tear-Off OFF BOTTOM FEED Form Tear-Off OFF 3 Press ITEM (4) until Form Tear-Off appears in the second column. 4 Press SET (5) until the time interval you wish to select appears in the third column. 5 Press SHIFT (2) + SEL (1) to exit Menu Mode and save the setting. User's Guide: English | 49 Automatic Forms Tear-Off Forms Tear-Off must be set to ON in the menu for Automatic Forms Tear-Off to occur. Automatic Forms Tear-Off automatically moves the paper from the initial printing position (print start position) to the tear-off position, after a time interval which you select through the menu. Paper remains in the tear-off position until the printer receives more data. 2 Remove the access cover and the pull-up roller assembly. 32T-02. eps and 32T-04UP. eps SEL ! CAUTION!Once the expanded printhead gap is engaged, you cannot print on single sheets without changing the gap back. If you try to print on single sheets without adjusting the printhead gap, you can damage the printhead and void your warranty. To disengage the expanded printhead gap, reverse the following steps. SEL MENU SHIFT LF Micro Feed Down EXIT POWER FF/LOAD Micro Feed Up TEAR PARK QUIET ALARM GROUP PRINT ITEM MENU SET PRINT QUALIT Y HSD NLQ UTL SSD TOF CHARA CTER 17 PITCH 10 12 20 15 PROP 3 Move the printhead to the center of the platen. 4 Remove the ribbon cartridge. 32T-19_up. eps 56 | Microline 390/391 Turbo 5 Swing up the printhead clamp, then remove it by pushing forward (toward the platen) and to the left. 32T-hg01. eps and 32T-hg02. eps 7 Lift the printhead plate off the carriage assembly (1). 32T-hg04. eps CHT HEISS 55091 086 CAUTION ATTENTION HOT CHAUD VORSI 1 HEISS 55091 086 CAUTION ATTENTION HOT VORSICHT CHAUD 6 Remove the printhead. 32T-hg03. eps 8 Turn the printhead plate around and reinsert it on the other side of the carriage assembly (1). 32T-hg05. eps SICH 5 5 0 9 1 T HEISS 086 T CAUTION ATTENTION HOT VOR CHAUD 1 User's Guide: English | 57 9 Replace the printhead, making sure that the circuit board at the bottom of the printhead firmly engages the slot (1) in the carriage. 32T-hg06. eps 10 Reinstall the printhead clamp and swing it back over to lock the printhead in place. 32T-hg07. eps 5 5 0 9 1 T HEISS 086 CAUTION ATTENTION HOT VORSICH CHAUD 1 ! CAUTION!Be sure the printhead is fully inserted before proceeding. ! Important!The clamp must be between the black projection on the printhead and the metal plate on the carriage, on both sides. 58 | Microline 390/391 Turbo 11 Reinstall the ribbon cartridge. 32T-19dn. eps 12 Replace the pull-up roller assembly and the access cover, then turn the printer on. 32T-04DN. eps and 32T-02. eps 13 Change the printer's secondary menu (make sure paper is loaded!) to engage the expanded printhead gap: a) Press SEL + TEAR while turning the printer back on. b) Press LF to advance through the menu to the Technical group (last option in menu). e) Press SHIFT + MENU to exit the menu and save your setting. SEL SEL MENU SHIFT LF Micro Feed Down EXIT POWER FF/LOAD Micro Feed Up TEAR PARK QUIET ALARM GROUP PRINT ITEM MENU SET PRINT QUALIT Y HSD NLQ UTL SSD TOF CHARA CTER 17 PITCH 10 12 20 15 PROP User's Guide: English | 59 Print Quality ! Important!Front panel settings for print quality and character pitch are overridden by software commands. The lights will always reflect the printer's state. 390 Panel. eps PRINT QUALITY LQ UTILITY COURIER PRESTIGE ROMAN SWISS GOTHIC ORATOR Press PRINT QUALITY to select: LQ: Letter Quality · Highest quality, slowest speed · Seven typefaces · Recommended for correspondence Utility · Medium quality, medium speed · Gothic font only · Recommended for internal documents and high-volume data. [. . . ] These are some of the things to look for: -- The power cord or plug is frayed or damaged. -- Liquid has been spilled into the housing, or the printer has been exposed to water. -- The printer doesn't function normally when you're following the operating instructions. 118 | Microline 390/391 Turbo ENERGY STAR® Regulatory Information Year 2000 Compliance This product is Year 2000 Compliant. It contains information technology that accurately processes date and time data between the years 1999 and 2000, and carries no issue for the September 9, 1999 (9999) programming concern. [. . . ]