User manual KYOSHO CALMATO 40 SPORTS EXPLODED VIEW

[. . . ] All Rights Reserved Document: MICROLINE CALMATO 40 SPORTS User's Guide Revised Edition: July, 2004 Written and produced by the Oki Data Training and Publications Department. Please address any comments on this publication to: Oki Data Americas, Inc. Mount Laurel, NJ 08054-4620 We invite you to visit Oki Data's multilingual web site at: http://www. okidata. com. KYOSHO, Oki Data and MICROLINE are registered trademarks of Oki Electric Industry Company, Ltd. Epson is a registered trademark of Seiko Epson Corporation (SEC), registered in the U. S. [. . . ] Move the paper lever (1) -- on the right side of the printer -- toward the rear of the printer, to the single sheet symbol. 3. Ensure that the printer is off-line (SELECT light off): press SELECT if necessary. If you are using paper wider than 8. 5 inches (216 mm), move the sprocket wheels to their outermost position: a. Pull the lock levers (A) at either end forward and move the sprocket wheels (B) as needed. 26 · Setting Up Your Printer c. Push back on the levers to lock the sprocket wheels in position. 5. Raise the paper separator. 27 · Setting Up Your Printer 6. Adjust the sheet guide (3) on the paper separator to position the left edge of the sheet, then insert a single sheet along the guide until it reaches the pinch roller. 7. Pull the bail arm lever (2) toward the front of the printer. 28 · Setting Up Your Printer 8. Use the platen knob to wind the paper through to the front of the printer and adjust the top of form. Press the TOF SET button while the printer is deselected (SELECT light offf) to set top of form. 9. Push back the bail arm lever, ensuring that the paper has been positioned correctly. Press TOF SET once or twice until the emulation you wish to engage appears in the right-hand column. Each time you press TOF SET, a new line prints and the setting which appears in the last column changes. For example: Printer Control Printer Control Emulation Mode Emulation Mode Epson ML 6. Press PITCH and MODE together to save your setting and exit the printer menu. 41 · Setting Up Your Printer Operating Your Printer Front Panel Operation Front Panel Lights LED Status, Function On = Printer is on line. Flashing = flashes with ALARM light to indicate a fault has been detected. Off = printer is turned off. The one lit indicates which character pitch --in characters per inch (cpi)-- is engaged. 42 · Operating Your Printer LED Status, Function The one lit indicates which print mode is engaged: NLQ = Near Letter Quality UTILITY = Draft mode HSD = High Speed Draft mode, or SSD (Super Speed Draft) if 12 cpi is selected. 43 · Operating Your Printer Front Panel Buttons Button Print Mode Advances the paper one line Menu Mode Scrolls through the printer menu groups. LINE FEED + SELECT = Initiates Rolling ASCII test (see page 60). FORM FEED + SELECT = Places Advances the paper to the next top of form or ejects single sheet from the printer. Sets a new top of form (TOF) position. Scrolls through the items for each menu group. printer in hex dump mode (see page 60). Sets printer to 17 cpi. Scrolls through the settings for each item within a group. Prints list of current menu settings. Toggles the printer on and off line. Places printer in Menu Mode. Selects the character pitch setting (cpi). Sets print mode (NLQ, Utility, HSD). PITCH + MODE Not applicable. = save settings and exit to print mode. PITCH + MODE Not applicable. = save settings and exit to print mode. 44 · Operating Your Printer Setting Printer Defaults The printer has an internal menu containing a number of default parameters which can be set to enable your printer to match the parameters required by your computer. Using the Menu Mode Entering the Menu Mode To enter the Menu Mode, press SELECT while turning on the printer. [. . . ] Make sure the printer is turned off, then press and hold LINE FEED while turning the printer on. To stop the test, press SELECT or turn the printer off. Note The top of each test printout contains information about your printer. Be sure to have a copy of the printout handy if you have to call for service. 62 · Maintenance Rolling ASCII Test The Rolling ASCII Test produces a continuous sampling of ASCII characters using the default type style. With the printer turned off, press and hold SELECT and LINE FEED while turning the printer on. [. . . ]