User manual KYOCERA LDC-780

[. . . ] Refer to them as necessary. Quick Installation Guide Safety Guide Safety Guide (FS-2100D/ FS-2100DN/LDC-780/ FS-4200DN/FS-4300DN) Describes the procedures for installation of the machine. Provides safety and cautionary information for the installation and use of the machine. Describes the machine installation space, cautionary space, and other information. Be sure to read this guide before using the machine. Product Library disc Operation Guide (This Guide) Describes how to load paper, basic print operations, and troubleshooting. Command Center RX User Describes how to access the machine from a computer via a Web browser to Guide check and change settings. [. . . ] The options available in Buzzer are as follows: • Key Confirmation (Key confirmation tone setting). . . 4-79 • Job Finish (Job completed tone setting). . . 4-79 • Ready (Preparation completed tone setting). . . 4-80 • Error (Error tone setting). . . 4-80 • Keyboard Confirm (Keyboard confirmation tone setting). . . 4-80 Buzzer: a b 1 Key Confirmation ********************2 Job Finish 3 Ready [ Exit ] 1 2 In the Device Common menu, press  or  to select Buzzer. The Buzzer screen appears. Key Confirmation (Key confirmation tone setting) When On is selected in this setting, a tone sounds each time a key is used. The default setting is On. 1 Key Confirmation: a b 1 Off 2 *On ********************- In the Buzzer menu screen, press  or  to select Key Confirmation. The Key Confirmation screen appears. 2 3 4 Press  or  to select whether the key confirmation tone is enabled. The key confirmation tone setting is set and the Buzzer menu reappears. Job Finish (Job completed tone setting) When On is selected in this setting, a tone sounds when printing ends. The default setting is Off. Job Finish: a b 1 *Off ********************2 On 1 2 In the Buzzer menu screen, press  or  to select Job Finish. The Job Finish screen appears. 3 Press  or  to select whether the printing completed tone is enabled. 4-79 Operation Panel 4 Press [OK]. The printing completed tone setting is set and the Buzzer menu reappears. Ready (Preparation completed tone setting) When On is selected in this setting, a tone sounds when print preparation has been completed. The default setting is Off. Ready: a b 1 *Off ********************2 On 1 2 In the Buzzer menu screen, press  or  to select Ready. The Ready screen appears. 3 4 Error (Error tone setting) Press  or  to select whether the preparation completed tone is enabled. The preparation completed tone setting is set and the Buzzer menu reappears. When On is selected in this setting, a tone sounds when a problem such as running out of paper or a paper jam occurs during printing. When you have completed the setting, exit the menu and restart the printer. The selected setting is valid after the printer starts up again. Format SSD (Formatting the SSD) When an optional SSD (HD-6) is inserted into the printer for the first time, it must be formatted before use. This menu is displayed only when the HD-6 is installed on the printer. Note If the HD-6 is installed in the printer, the Document Box will be available. Formatting will destroy any existing data on a storage device including a used HD-6. When the HD-6 has not yet been formatted, the Attention indicator flashes and Format SSD is displayed. Use the procedure below to format the HD-6. When a new HD-6 is inserted in the printer's slot, Format SSD will appear on the message display. 1 In the Device Common menu, press  or  to select Format SSD. 4-82 Operation Panel Format. Pressing [No] ([Right Select]) returns to the Device Common menu without formatting the SSD. Format SD Card (Formatting the SD/SDHC memory card) The printer is equipped with a slot for an SD/SDHC memory card. For details about the handling of the SD/SDHC memory card, refer to Installing and Formatting the SD/SDHC Memory Card on page A-9. A new SD/SDHC memory card must be formatted before it can be used in the printer. Formatting allows data to be written to the SD/SDHC memory card. IMPORTANT Format SD Card is only displayed when an SD/SDHC memory card is installed in the printer and protection is disabled. Note Formatting will destroy any existing data on a storage device including a used SD/SDHC memory card. [. . . ] In 1996, Level 3 was released as an update for the Internet access and PDF format as well as gradual improvements in implementation technologies. PPM (Prints Per Minute) This indicates the number of A4 size printouts made in one minute. Printer driver The software to enable you to print data created on any application software. The printer driver for the machine is contained in the Product Library disc enclosed in the package. Install the printer driver on the computer connected to the machine. RA (Stateless) The IPv6 router communicates (transmits) information such as the global address prefix using ICMPv6. ICMPv6 stands for Internet Control Message Protocol, and is an IPv6 standard defined in the RFC 2463 "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification". SD/SDHC Memory Card An SD Memory Card is a removable storage media. [. . . ]