User manual KYOCERA KM-C2630

[. . . ] KM-C2630/C2630D Printer Option Operation Guide <Functions Edition> Introduction I 1. KX Driver (Specific function) I Link to the KX Printer Drivers Operation Guide Introduction About this Operation Guide This Operation Guide is included with your Printing System (N) and should be read in combination with the Operation Guide <Set-Up Edition> for that product. This Operation Guide contains information on making settings in your printer. The explanations in this Operation Guide were written with the assumption that the user has a basic understanding of how to work in Microsoft Windows. [. . . ] The RAM disk function is not available when the optional hard disk is installed. [Proof and Hold] and [Stored job print out] of the e-MPS function (P4-49) are available. The RAM Disk is created from that portion of the printer's memory that is normally available to the user. Thus, if the size of the RAM disk created is too large, printing speed may actually be decreased or the machine may run out of available memory. WARNING: Resetting the printer or turning the main switch OFF will erase all data written to the RAM Disk. In order to create a RAM Disk, make the necessary settings as shown below. About the RAM disk settings It is possible to perform RAM disk settings for the 10 items shown in the following chart. For the most efficient use of the printer functions, select the various settings according to your printing needs. Item 1 RAM disk On/Off Available settings On, Off Remarks This setting must be turned On in order to sort print sets using the collating function. Displayed only when "On" is selected under the "1 RAM disk On/Off" setting. 2 Writing data If "Write Data" is selected here, the machine will enter a "waiting for data" state until data is sent from the host computer. Partition List print out Write Data 3 List of Partitions Displayed only when "On" is selected under the "1 RAM disk On/Off" setting. Displayed only when "On" is selected under the "1 RAM disk On/Off" setting. 4 RAM disk size Sets the amount of memory that will be used as a RAM disk. The maximum size that can be selected is the total amount of memory installed minus the amount used by the system (36 MB). Reading data Reads the selected data from the RAM disk. 01 ­ 99 MBytes 5 Select from among the data partition names that are displayed. · Displayed only when there is appropriate data in the RAM disk. · Displayed only when "On" is selected under the "1 RAM disk On/Off" setting. · Displayed only when there is appropriate program data in the RAM disk. · Displayed only when "On" is selected under the "1 RAM disk On/Off" setting. · Displayed only when there is appropriate data in the RAM disk. · Displayed only when "On" is selected under the "1 RAM disk On/Off" setting. · Displayed only when there is appropriate font data in the RAM disk. · Displayed only when "On" is selected under the "1 RAM disk On/Off" setting. 6 Reading program data Reads the selected program data from the RAM disk. Select from among the program partition names that are displayed. 7 Deleting data Deletes the selected data from the RAM disk. Select from among the data partition names that are displayed. 8 Deleting font data Deletes the selected font data from the RAM disk. Select from among the fonts that are displayed. 4-25 4. Selecting the Printer Settings Item 9 Deleting program data Deletes the selected program data from the RAM disk. Available settings Select from among the program partition names that are displayed. Remarks · Displayed only when there is appropriate program data in the RAM disk. · Displayed only when "On" is selected under the "RAM disk On/ Off" setting. [. . . ] Hard Disk If the optional hard disk is installed in this machine, received and rasterized data can be saved onto that disk. When printing out multiple sets of the same documents, this allows faster printing with the collating function as well as enabling the use of the e-MPS function. Serial Interface Option Install the serial interface in this machine when the serial port is used for printer interface. 5-1 6. KX Driver (Specific function) The following section explains the specific functions of the KX driver. [. . . ]