User manual KYOCERA KM-6030

[. . . ] In this guide, 6030 refers to the 60 cpm (copies per minute) model and 8030 to the 80 cpm model. NOTE: This Operation Guide contains information that corresponds to using both the inch and metric versions of these copiers. The inch versions of these copiers are shown in the screens in this guide. If you are using the metric version, use the messages provided for the inch version as reference only. [. . . ] Plain, Transparency, Rough, Vellum, Labels, Recycled, Preprinted, Bond, Cardstock, Color (Colour), Prepunched, Letterhead, Thick paper, Envelope, High Quality and Custom 1-8 1 Press the System Menu/Counter key. 2 Press [MP tray Setting]. System Menu / Counter System Menu Copy Default Language MP tray Setting Machine Default Document Management Register Orig. Size Job Accounting BOX Management Print Report 3 Press [Select Paper Type]. m Menu / Counter Back Unit Paper Type Close Centimeter Inch Plain Select Paper Type 2-14 Preparing to Copy 4 Select the paper type. System Menu / Counter Select Paper Type Back Plain Transparency Rough Vellum Labels Recycled Preprinted Bond Cardstock Color Prepunched Letterhead Thick paper Envelope Custom 1 Custom 2 Custom 3 Custom Custom Custom Custom High Quality Custom 4 5 6 Press [Close]. The touch panel will return to the [Basic] screen. 2-15 Preparing to Copy Loading Originals Loading Originals in the Document Processor The document processor automatically scans each sheet of multiple originals individually. Items Weight Size Capacity Specifications 45 g/m² to 160 g/m² Minimum: 5 1/2 × 8 1/2" (A5R); Maximum: 11 × 17" (A3) Standard paper (80 g/m²), colored paper or recycled paper: 200 sheets (30 sheets in Auto Selection mode) Coated paper: 1 sheet High quality paper, 50 g/m²: 200 sheets High quality paper, 110 g/m²: 145 sheets Precautions on Types of Originals for Document Processor Do not use the document processor for the following types of originals. In addition, if originals have punched holes or perforations, load them with the holes or perforations away from the leading edge. · · · · Transparencies such as for overhead projectors Delicate originals such as carbon paper, crumpled paper, or vinyl sheets Irregularly shaped (non-rectangular) originals, wet originals, or originals containing adhesive tape or glue Originals bound with clips or staples. (To avoid jams, remove the clips or staples and straighten any curls, wrinkles, or creases before loading them. Failure to do so may cause the originals to jam. ) Originals with cut-out sections or with very slippery surfaces Originals with correction fluid which is not dried Originals with folds. Failure to do so may cause the originals to jam. ) · · · How to Load Originals Follow these steps to load originals in the document processor. IMPORTANT: Before loading originals, be sure there are no originals left on the original eject table. Originals left on the original eject table may cause the new originals to jam. 2-16 Preparing to Copy 1 Adjust the original width guides to fit the originals. 2 Place the originals. Put the side to be copied (or the first side of two-sided originals) face-up. Slide the leading edge into the document processor as far as it will go. IMPORTANT: Confirm that the original width guides exactly fits the originals. Pull out the ejection guide for originals of 8 1/2 × 14" (B4) or 11 × 17" (A3). Ensure that loaded originals do not exceed the level indicated. Exceeding the maximum level may cause the originals to jam. 2-17 Preparing to Copy Loading Originals on the Platen To copy books, magazines, or other originals that cannot be loaded in the document processor, open the document processor and place the original directly on the platen. Adjust how the document processor opens by using the document processor angle adjustment lever. Move the lever left to open the document processor 60° and move it right to open the document processor 30°. IMPORTANT: Before opening the document processor, be sure that there are no originals left on the original table or on the original eject table. Originals left on the original table or on the original eject table may fall off the copier when the document processor is opened. Do not move the document processor angle adjustment lever when the document processor is open. Close the document processor before using the lever. 1 Open the document processor. 2 Place the original. Put the copying side facedown and align it flush against the original size indicator plates with the back left corner as the reference point. Inch models 2-18 Preparing to Copy Metric models 3 Close the document processor. [. . . ] Jammed paper will be pushed to the paper conveyor. 6-17 Troubleshooting 5 Pull the lever A2 and slowly pull out the paper conveyor. Warning High voltage is present in the charger section. Take sufficient care when working in this area, as there is a danger of electrical shock. Caution The fixing unit is extremely hot. Take sufficient care when working in this area, as there is a danger of getting burned. 6 Remove the paper from above the paper conveyor. 7 Open the cover A4. 8 Remove the jammed paper. [. . . ]