User manual KYOCERA KM-4530

[. . . ] 4530/5530 Operation Guide Please read the Operation Guide before using the copier. Keep it close to the copier for easy reference. Off Mode The device automatically enters "Off Mode" when 90 minutes have passed since the device was last used. The amount of time of no activity that must pass before "Off Mode" is activated may be lengthened. We have determined as a participating company in the International Energy Star Program that this product is compliant with the standards laid out in the International Energy Star Program. [. . . ] Inch specifications 2 Printing out stored documents Perform the following procedure when you want to print out documents that are stored in a shared data box. 1 Original Register 11x81/2" 81/2x11" 25/10/'01 19:20 Cancel Press the [Document Management] key. The "Document Management" screen will be displayed. Ready to register document(s). Place originals then press Start key. Document registration Shared Data Box Job Job006 Auto Select orig. size Change name Basic 1 sided Original type 100% Reduce /Enlarge Quality Back Edge Orig. set direction Edit Metric specifications Ready to register document(s). Set original. Press Start key. Form registration Shared Data Box Job Job001 Auto size Select regi. 1-sided Original type 100% Reduce/ Enlarge Quality Original A4 Register A4 25/10/'01 19:20 Job cancel Back Edge Orig. set direction Edit 2 Touch the "Document printing" key under "Shared Data Box". Inch specifications Select function. Document Management 25/10/'01 19:20 End Synergy Print Box Form box NOTE Refer to "Entering characters" on page 7-75 for information on entering characters. Shared Data Box Document reg. size" ["Select size orig. "] key, the "Select regi. size" key, the "Original type" key, the "Reduce/ Enlarge" key and/or the "Orig. set direction" key, if you want to perform the corresponding settings. If you want to access the "Scanning density" key and/or the "Orig. image quality" ["Image quality"] key to make those settings, touch the "Quality" key. If you want to set access the "Border Erase" ["Erase Mode"] key and/or the "Continuous scanning" ["Multiple scanning"] key to make those settings, touch the "Edit" key. Metric specifications Select function. Document Management Shared Data Box Synergy Print Box Form box 25/10/'01 19:20 End Document registr. Once all of the documents have been completely scanned, the touch panel will return to the screen in step 3. If you want to register another document, repeat steps 3 through 6. Select the documents to be printed out and then touch the "Finish selecting" key. Inch specifications Document printing Document data box Job 005 Job 004 Job 003 Job 002 1 1 1 1 1 Cancel Order of indication Conf/Crrt. details Up 25/10/01 25/10/01 25/10/01 25/10/01 25/10/01 001/010 Down 7 Touch the "End" key. The touch panel will return to the contents of the "Basic" tab. Job 001 Finish selecting Document Management - Shared Data Box Metric specifications Document printing Document data box JOB003 JOB002 JOB001 1 1 1 Job cancel Order of indication Check/Rev. details Up 25/10/01 25/10/01 25/10/01 Down 001/003 Document Management - Shared Data Box Finish Selecting 6-5 Section 6 DOCUMENT AND OUTPUT MANAGEMENT FUNCTIONS NOTE It is possible to change the order of display for the stored documents. To do so, touch the "Order of indication" key, and then touch the "Sort by date" key or the "Sort by name" key, as appropriate. 3 Checking stored documents and changing their names Perform the following procedure when you want to verify the name of stored documents, the size of the original documents or the date and time they were stored in the shared data box, or when you want to print out the first page of those document in order to check them. You can also use this procedure to change the registered name for the documents. 4 Touch the "Select paper" key, the "Sort/Finished" key and/or the "1 sided/ 2 sided" key, to perform the corresponding settings. If you want to access the "Form Overlay" key, the "Margin" key, the "Cover Mode" key, the "Page #" key, the "Booklet" key and/or the "Select of Output" key to make those settings, touch the "Edit" key. 1 Press the [Document Management] key. [. . . ] without certification, and applies to laser products manufactured after Aug. The label shown below indicates compliance with the CDRH regulations and must be attached to laser products marketed in the United States. Optical unit When checking the optical unit, avoid direct exposure to the laser beam, which is invisible. Shown at left is the label located on the cover of the optical unit. 4. [. . . ]