User manual KYOCERA KM-2530

[. . . ] Operation Guide * The above illustration includes the optional original cover. Keep it close to the copier for easy reference. G Off Mode The device automatically enters "Off Mode" when 60 minutes have passed since the device was last used. The amount of time of no activity that must pass before "Off Mode" is activated may be lengthened. G Sleep Mode (If the copier has printer and/or facsimile function) The device automatically enters "Sleep Mode" when 60 minutes have passed since the device was last used. [. . . ] Control returns to the "Default setting menu" screen. 6-9 7 (See the Instruction manual for the optional printer. ) ­ 8 6-2 CHAPTER 6 COPIER MANAGEMENT (2) How to display the "Management code menu" screen Display the "M anagement code menu" screen. 4 1 Press the [ ] (Default setting) key on the control panel. Enter the 4-digit management pin code " " with the numeric keys. "2500" for Copiers with a copy speed of 25 copies per minute, "3500" for Copiers with a copy speed of 35 copies per minute or "4000" for Copiers with a copy speed of 40 copies per minute is set at the shipment. Inch specifications Selection Management Interrupt E 1 4 7 2 5 8 3 6 9 Reset Stop/ Clear Metric specifications 2 The "Default setting menu" screen will appear. Inch specifications 5 Metric specifications NOTE Select any of the management setting items. The selected setting screen will appear. · The 4-digit management pin code can be changed. (See "Management code change" on page 6-21. ) · See the following "(3) How to make various settings" and make settings. (3) How to make various settings 3 Touch the [Management] key. Inch specifications · Registering new ID codes Register a new 8-digit (Max. ) ID code, and then set the maximum number of copies. 1 Display the "Management code menu" screen. (See (2) How to display the "Management code menu" screen. ) Inch specifications Metric specifications Metric specifications 6-3 CHAPTER 6 COPIER MANAGEMENT 2 Touch the [ID-code Reg. /Del. ] key. Inch specifications 5 Touch the lower-side [# keys] key, and then enter the maximum number of copies (1, 000 to 999, 000) with the numeric keys. Inch specifications Metric specifications Metric specifications 3 Touch the [Register] key. Inch specifications NOTE · Entering "0" enables unlimited copying. · Touch the [Back] key to display the "Register/Delete" screen. Re-enter the ID code and the maximum number of copies. 6 Metric specifications Touch the [Close] key. Inch specifications Metric specifications 4 Touch the upper-side [# keys] key, and then enter ID code(8-digit: 0 to 99999999) with the numeric keys. Inch specifications NOTE · To register a new ID code, touch the [Next Register] key, and then repeat steps 4 to 6. Metric specifications 6-4 CHAPTER 6 COPIER MANAGEMENT 7 Touch the [Close] key . Inch specifications Metric specifications Metric specifications 8 Touch the [On] key below "Copy", and then touch the [Close] key. "Enter ID- code" screen will appear every time you start up the copier. Inch specifications 3 Select the ID code to be deleted, and then touch the [Delete] key. The message "Are you sure you want to delete this IDcode?" will appear. Inch specifications Metric specifications Metric specifications · Deleting ID codes Delete the ID codes already registered. 4 NOTE 1 Display the "Management code menu" screen. (See (2) How to display the "Management code menu" screen. ) Inch specifications Make sure to check the code to be deleted, and then touch the [Yes] key. The "Register/Delete" screen will appear. · To delete other ID code, repeat steps 2 to 4. Metric specifications 6-5 CHAPTER 6 COPIER MANAGEMENT 5 Touch the [Close] key. [. . . ] Safety switch The power to the laser unit is cut off when the front cover is opened. CAUTION! The power plug is the main isolation device!Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source. ATTENTION! Le débranchement de la fiche secteur est le seul moyen de mettre l'appareil hors tension. Les interrupteurs sur l'appareil ne sont que des interrupteurs de fonctionnement : ils ne mettent pas l'appareil hors tension. WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ]