User manual KYOCERA KM-2020

[. . . ] KM-1620 KM-2020 Please read the Operation Guide before using the copier. Keep it close to the copier for easy reference. In areas of the GEEA, the available setting for the Off Mode to engage is between 1 and 120 minutes, and the available setting for the Low Power Mode to engage is any 1 minute, 5 minutes, 15 minutes, 30 minutes, 45 minutes, 60 minutes, 90 minutes or 120 minutes. This Operation Guide mentioned that the KM-1620 is a 16-sheet copier and the KM-2020 is a 20-sheet copier. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Legal Restriction On Copying · It may be prohibited to copy copyrighted material without permission of the copyright owner. [. . . ] Sets the time interval prior to the automatic operation of the Auto Clear function when on (Enable) has been selected as the Auto Clear setting. Sets the time interval prior to the automatic engagement of the Low Power mode after copy operations have been completed. Sets the time interval prior to the automatic operation of the Auto Clear function when on (Enable) has been selected as the Auto Clear setting. The Alarm can be set to sound when a key on the Operation Panel is pressed or in cases when errors occur, etc. 10 - 270 (10-second units) (*90) 6-29 F34 Auto Clear Time 6-30 F35 Low Power Mode Transition Time Off Mode Transition Time 1, 5, 15, 30, 45, 60, 90, 120, 180, 240 (minutes) (*15) 1, 5, 15, 30, 45, 60, 90, 120, 180, 240 (minutes) (*30) 6-31 F36 6-31 F37 Alarm on: Enabled (sound alarm) oFF: Disabled (no alarm)* 6-32 F38 Toner Coverage Report Prints out a report that shows the number of copies --made and the average amount of toner used (blackness ratio %) for each paper size. 6-33 6-10 Section 6 COPIER MANAGEMENT Default Settings Mode Operations Procedures Follow the procedure listed below to operate in the [Default Settings Mode]. 4 Press the [Enter] key. Inch specifications Metric specifications 1 Depress the [Exposure Adjustment] keys on both sides for 3 seconds. of Copies display. Procedure for Changing the Default Settings The procedure for changing each of the items in the Default Settings is described below. Press either the Zoom (+) key or the Zoom (­) key and select each Default Settings Mode. Inch specifications Metric specifications 2 User Status Report Outputs a list of the values set for the Default Settings items. Note Check to make sure that 11" × 8 1/2"/A4 size paper is loaded in the drawer. 1 Display the Default Settings Mode. (Refer to P. 6-11 "Default Settings Mode Operations Procedures". ) Inch specifications Metric specifications Notes · Each of the Default Setting Modes can be selected by pressing the Keypad keys. · Refer to "Procedure for Changing the Default Settings" regarding the following. 3 After completing each operation, press on the Zoom (+) or Zoom (­) key to display "F00". Inch specifications Metric specifications 2 Press either the Zoom (+) or Zoom (­) key to display "F01". Inch specifications Metric specifications 6-11 Section 6 COPIER MANAGEMENT 3 Press the [Enter] key. Inch specifications Metric specifications 2 Press either the Zoom (+) or Zoom (­) key to display "F02". Inch specifications Metric specifications Sample: User Status Report 3 Press the [Enter] key. Inch specifications Metric specifications 4 Press either the Zoom (+) key or the Zoom (­) key and select "1- (Text + Photos)", "2- (Photos)" or "3- (Text)". Inch specifications Metric specifications 5 Original Image Quality Sets the original image quality that will be selected at the time the copier is turned on. Press the [Enter] key. Inch specifications Metric specifications 1 Display the Default Settings Mode. (Refer to P. 6-11 "Default Settings Mode Operations Procedures". ) Inch specifications Metric specifications 6-12 Section 6 COPIER MANAGEMENT Exposure Mode Sets the copy exposure at the time the copier is turned on to Manual or Automatic. 5 Press the [Enter] key. Inch specifications Metric specifications 1 Display the Default Settings Mode. (Refer to P. 6-11 "Default Settings Mode Operations Procedures". ) Inch specifications Metric specifications Eco-copy 2 Selects the initial value of Eco-copy when the power is turned on. Press either the Zoom (+) or Zoom (­) key to display "F03". [. . . ] 5-8 Making enlarged and reduced copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Margin Shift (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25 Merge Copy Borderline (Default Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-27 Mixed Original Sizes (Auto Selection) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]