User manual KYOCERA KM-1500

[. . . ] 1500 Please read the Operation Guide before using the copier Keep it close to the copier for easy reference All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher. Legal Restriction On Copying · It may be prohibited to copy copyrighted material without permission of the copyright owner. · It is prohibited under any circumstances to copy domestic or foreign currencies. [. . . ] Scanning of the first original will start. NOTES · If the optional Document Processor is installed on your copier, the Sort mode will be selected automatically once originals are set there. · If the optional Document Processor is installed on your copier, all of the originals set there will be scanned and the copy operation will start. 5-9 Section 5 COPY FUNCTIONS Program function By registering often used settings in advance as a single program, it is possible for you to make copies using those same settings by simply pressing the Program key. Using programmed settings to make copies 1 Press the Program key. The Program indicator will light and the registered settings will be shown on the operation panel. NOTE A single combination of copy modes and other functions displayed on the operation panel can be registered as a program using this function. 2 Registering the program Make copies as desired. 1 2 Set the desired copy modes and functions that you want to register as the program. Press down on the Program key for at least 3 seconds. 3 The Program indicator will flash twice and registration of the program is complete. NOTES · Copying is now possible at any time using the settings that were registered as the program. · If you want to clear the settings that are currently registered as the program, simply press the Reset/Power key while the Program key is lit. 5-10 Section 6 COPY DEFAULT SETTINGS Available default items The state that the copier enters at the end of warm-up or when the Reset/Power key is pressed is called the "initial mode". The modes, functions and other settings that are automatically pre-set for use in the initial mode are called "default settings". These default settings can be changed as desired to suit your copying needs. Each default item, as well as each of the available settings for each item, are represented by code numbers on the copy quantity/magnification display. Refer to the "Available settings" column in the following tables for the code number that correspond to each setting value. The factory default setting is indicated by an asterisk. Item number F00 F01 F02 Default Quit Default Settings User Copy Setting List Image Quality Mode Description Quits the default settings and returns the copier to a copy-ready state. Sets the image quality mode that will be selected at the time the copier is turned on. Available settings ----1-: Auto exposure adjustment mode 2-: Text & Photo mode* 3-: Photo mode 4-: Text mode 5-: Eco-copy mode 1-: 5 steps* 2-: 7 steps Reference page --6-6 6-6 6-9 F03 Exposure Steps Changes the number of exposure steps during manual adjustment of the copy exposure in all image quality modes, except for the Auto Exposure Adjustment mode. Changes the overall copy exposure when using the Auto Exposure Adjustment image quality mode. Adjusts the exposure for when the Text & Photo mode is selected as the image quality mode. Adjusts the exposure for when the Photo mode is selected as the image quality mode. The larger the code number, the darker the exposure. 6-6 6-9 F04 Auto Exposure Adjustment 1-: 1 Lightest 2-: 2 3-: 3* 4-: 4 5-: 5 Darkest 1-: 1 Lightest 2-: 2 3-: 3* 4-: 4 5-: 5 Darkest 1-: 1 Lightest 2-: 2 3-: 3* 4-: 4 5-: 5 Darkest 6-6 6-9 F05 Text & Photo Mode Exposure Adjustment 6-6 6-9 F06 Photo Mode Exposure Adjustment 6-6 6-9 6-1 Section 6 COPY DEFAULT SETTINGS Item number F07 Default Text Mode Exposure Adjustment Description Adjusts the exposure for when the Text mode is selected as the image quality mode. If black lines appear on copies when you feed originals from the Document Processor (but they do not exist on the originals themselves), this function will make them less apparent. If Black Line Correction is turned on, however, small and/or detailed text may not be reproduced as clearly as before, so it is normally recommended that you do not change this function from its factory default setting. * Black Line Correction is not available when the Photo mode is selected as the image quality mode. Copies will come out clearer if you select "Error diffusion" when using originals with both text and photos and "Dithering" when using originals with mainly photos. Sets the location for feeding paper that will be automatically selected at the end of warm-up, or when the Reset/Power key is pressed. * If the optional Paper Feeder is not installed on your copier, this default setting will not appear. Sets whether the Auto Drawer Switching function (see page 2-5) will be used or not. [. . . ] 7-1, 9-9 Original jam in the optional Document Processor . . . . . . . . . . . . . . . . . . . . . . . 8-7 D Default Drawer (default setting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Document Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]