User manual KYOCERA FS-C5150DN

[. . . ] OPERATION GUIDE FS-C5150DN/FS-C5250DN FS-1100 FS-1300D Introduction Thank you for your purchase of FS-C5150DN/FS-C5250DN. This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a simple troubleshooting action as necessary, so that you can always use the machine in good condition. Please read this Operation Guide before you start using the machine, and keep it close to the machine for easy reference. We will not be liable for any damage caused by the use of third party supplies in this machine. A label shown in the illustration assures that the supplies are our own brand. Contents Menu Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] or repeatedly until >>XPS FitTo Page appears. 3 Press [OK]. A blinking question mark (?) appears. 4-44 Using the Operation Panel 4 5 6 Select On or Off using Press [OK]. or . Press [MENU]. The display returns to Ready. TIFF/JPEG Size (Print mode setting for TIFF/JPEG files) Use this setting to select the printing method used when TIFF or JPEG files are printed directly. or repeatedly until >>TIFF/JPEG Size appears. 3 Press [OK]. A blinking question mark (?) appears. 4 Press or repeatedly until the desired print mode is displayed. The list shows the following print modes: Paper Size (scaled to fit the paper size) Images are resized so that they fill the paper size when printed. Image Resolution (matched to the image resolution) Image files are printed at the resolution specified in the resolution information. Images with no resolution information are printed using the Paper Size setting. Print Resolution (matched to the print resolution) Images are printed using a 1-to-1 correspondence between the image file pixels and printed dots. For example, the printed size of a 600 × 300-pixel image file is 1 inch × 1/2 inch. 5 6 Press [OK]. The display returns to Ready. Note Images are automatically rotated during printing to provide a closer match between the aspect ratios of the image file and the paper used for printing. 4-45 Using the Operation Panel Network (Network settings) This printer supports TCP/IP and TCP/IP (IPv6) protocols. This printer routinely uses the TCP/IP (IPv4) protocol, but provides a separate setting for the nextgeneration IP, IPv6. TCP/IP (IPv4) uses 32-bit IP addresses, but the rapid growth in the number of Internet users has resulted in a shortage of IP addresses. IPv6 was developed to expand the range of available IP addresses by using 128-bit IP addresses. The options available in the Network settings are as follows: · TCP/IP (IPv4 settings) · TCP/IP (IPv6) (IPv6 settings) Note Check with your network administrator when selecting the network setting. After all network related settings have been done, turn the machine OFF and ON again. When COMMAND CENTER is used, network parameters and security settings can be conveniently changed and checked from your PC. For more information, refer to the COMMAND CENTER Operation Guide. 1 Network > Press [MENU]. Press or repeatedly until Network > appears. 2 TCP/IP (IPv4 settings) This selects the settings for TCP/IP (IPv4). The TCP/IP system refers to the Internet system, which has a 5-layer structure consisting of the interface layer, link layer, network (IP) layer, transport (TCP/UDP) layer and application layer. The interface layer is a key layer in the TCP/IP system that provides an abstracted interface that is not dependent on the link (communication line: frame relay or Ethernet, etc. ) to the IP module (IP layer). This means that the IP module can use this abstracted interface (which is not dependent on the link type) to exchange IP packets back and forth with the link layer. The options available in the TCP/IP (IPv4) settings are as follows: · DHCP (DHCP setting) · Auto-IP (Auto-IP setting) · IP Address (IP address setting) · Subnet Mask (Subnet mask setting) · Gateway (Gateway setting) · Bonjour (Bonjour setting) IMPORTANT The DHCP, IP address, subnet mask, gateway and Bonjour menu options for TCP/IP are displayed when TCP/IP is enabled. 1 Press while Network > is displayed. 4-46 Using the Operation Panel 2 >TCP/IP ? [. . . ] When no specific gateway is designated for a destination IP address, data is sent to the host that is designated as the Default Gateway. DHCP (Dynamic Host Configuration Protocol) This is a protocol that automatically resolves the IP address, Subnet Mask and Gateway address on a TCP/IP network. Use of DHCP minimizes the load of network administration, especially on network environments with a large number of client computers where it is not specifically necessary to assign a separate IP address to each client, including printers. dpi (dots per inch) This indicates the number of dots printed per inch (25. 4 mm) as a unit for expressing resolution. EcoPrint This is a printing mode that reduces toner consumption. Pages printed in the EcoPrint mode are lighter than pages printed in the normal mode. Emulation This refers to emulation of other manufacturers' printers. The printer emulates operation of the following printers: PCL6 and KPDL. Form Feed Timeout While data is being sent to a printer, some pauses may occur. [. . . ]