User manual KYOCERA FS-9000

[. . . ] 7DEOHRI&RQWHQWV 8VHU·V0DQXDO . \RFHUD/DVHU3ULQWHU )6 7KH)6LQWKLVSKRWRJUDSKLVHTXLSSHGZLWKWZRRSWLRQDOSDSHUIHHGHUV3) DQGDQRSWLRQDOGRFXPHQWILQLVKHU') Introduction Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software _____________________________________________________________________________________ SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S NATIVE MODE OR ONE OF ITS EMULATION MODES. The emulation mode can be changed by following the procedures described in Chapter 2. Notice ________________________________________________________________________________________________ The information in this manual is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. [. . . ] It is possible to set the partitions on the memory card which you wish to execute for the printer at power-on by using the PRESCRIBE 2e FRPO I0 command. For details on the FRPO command, please read the Programming Manual on the supplied CD-ROM. A font card can be read from the control panel or read automatically upon power-on or printer reset when a font card is inserted in the printer. Inserting Memory Card Carefully insert the memory card as far as it will go with the top side facing right (back side of the printer). Memory Card Slot Memory Card 2-40 Chapter 2 Operating the Page Printer Notes ____________________________________________________________________ Follow the precautions below when handling a memory card. · · · · · · · · · · Operating a Memory Card A memory card is sensitive to static electricity. Before handling a memory card, be sure to eliminate any static electricity which may have built up on your body or clothing by touching a metallic object. Be sure that its power is off when inserting or removing a memory card. Store a memory card in their protective case when not using them. The following operations on a memory card inserted into the printer's memory card slot are possible. · · · · · · · Reading Fonts Reading Macros Reading Data Writing Data Deleting Data Formatting Memory Card Printing a List of Data Names (Partitions) 2-41 Memory Card Note that only reading fonts and printing a list of partitions are possible when a font card is inserted. Each operation is described below. Reading Fonts from a Memory Card Fonts can be read into the printer's internal memory from an optional font card. The font read can then be selected from the printer's control panel. A font card is automatically read into the printer when the printer's power is turned on. The operation described here is performed while the message display reads Ready. 1. 5. Pressing the ENTER key again will cause Processing to appear in the lower part of the message display and font data to be read from the font card. After fonts have been read, the message display will return to >Read fonts. Pressing the EXIT key will cause the message display to return to Ready. 2-42 Chapter 2 Operating the Page Printer Reading Macros from a Memory Card Macro data on a memory card can be registered on the printer. Registered macro data can be used just like macro data located in printer memory. If a memory card already containing macro data is inserted in the printer, that macro data will be read into the printer automatically when the printer's power is turned on. The operation described here is performed when a memory card is inserted while the message display reads Ready. Note _____________________________________________________________________ Macro data on a memory card has no effect on printer memory. 1. Check that the memory card containing macro data is inserted. This display only appears if a memory card containing macro data is inserted. 5. Pressing the ENTER key again will cause Processing to appear in the lower part of the message display and macro data to be read from the memory card. After macro data has been read, the message display will return to >Read macro. Pressing the EXIT key will cause the message display to return to Ready. 2-43 Memory Card Notes ____________________________________________________________________ · · If the name of a macro on the memory card is the same as that in printer memory, the macro data on the memory card with the conflicting name will not be registered. Re-execute >Read macro if this happens. Reading Data (Partitions) from a Memory Card Specified data (partitions) on a memory card can be read into printer memory. 1. Bring up the menu >Read data on the message display. You can scroll through data names on the memory card one by one by pressing the + key. [. . . ] Press the ENTER key. If you want to re-enter a setting, press the CANCEL key before pressing the ENTER key. 7. This will enable currently selected settings. >NetWare Off On >TCP/IP Off On >Ether Talk >TCP/IP Off Off Number of copies 001 >OPT. StatusPage >TCP/IP Off Off > >>NetWare Frame Auto > >>DHCP OFF >>IP Address >>Gateway >>Subnet Mask Continued on next page (Continued from previous page) >Code set ISO-6 ASCII Emulation HP LJ 5M/5Si > (*1) Emulation KC-GL > >KC-GL Pen width >KC-GL Page set > >>Pen (1) width 01 dot (s) 01 dot (s) Emulation KPDL > >Print KPDL errs Off On (*2) Emulation KPDL (AUTO) > >Alt. Emulation HPLJ 5M/5Si >Print KPDL errs Off On (*2) Emulation IBM Proprinter Line Printer Emulation DIABLO 630 Emulation EPSON LQ-850 Font Bitmap Scalable > >Code set IBM US > >Code set DIABLO US >Code set LQ US >Bitmap font 00001 >Courier Dark Light >AudreyTwo-Regu lar SWC >Courier Dark Light >Size 012. 00 point (s) >Pitch 10. 00 cpi > > > (*3) *1: *2: Depending on the emulation selected, the following set >code sets are available. [. . . ]