User manual KYOCERA FS-6700

[. . . ] Table of Contents Users Manual Kyocera Laser Printer FS-6700 Introduction Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S NATIVE MODE OR ONE OF ITS EMULATION MODES. The emulation mode can be changed by following the procedures described in Chapter 2. Notice The information in this manual is subject to change without notification. [. . . ] A cursor "_" will flash and the current setting can be changed. If you want to change the setting, press the CANCEL key before pressing the ENTER key. Dumping Received Data It is possible to print data received by the printer as hexadecimal code for the purposes of debugging programs and files. Selecting Dump Received Data Mode 1. Press the + key several times to display >Print HEX-DUMP and press the ENTER key. Press the ENTER key again and >Processing will be displayed for awhile followed by Waiting. Once the dumped data you require has been output, it is possible to cancel the printing of any further dumped data by taking the printer offline by pressing the ON LINE key and then pressing the CANCEL key. 2-30 Chapter 2 Operating the Laser Printer 2. 9. KIR Level This printer incorporates the KIR (Kyocera Image Refinement) smoothing function. KIR provides high quality printing by providing a software-type improvement to the resolution. Print a status page to find out the current printing mode. The KIR setting is Off The KIR setting is On (Default setting) Notes q Set the print density to 03 when setting the KIR mode. q You can look at the check line, the last line on a KIR test page, to make the optimum KIR mode setting. Refer to the table on the next page. 2-31 2. 9 Status page KIR Checking Lines KIR Setting Optimized stripes Description The current KIR setting is optimal. Dark vertical stripes The KIR mode currently set is too strong. If you still get dark vertical stripes, adjust the print density control to a lighter setting. (See the Mode Select Menu at the end of this manual. ) The KIR mode currently set is too weak. If you still get white vertical stripes, adjust the print density control to a darker setting. (See the Mode Select Menu at the end of this manual. ) White vertical stripes 2-32 Chapter 2 Operating the Laser Printer Selecting KIR Mode 1. Press the + or ­ key to display >KIR mode and then press the ENTER key. If you want to change the setting, press the CANCEL key before pressing the ENTER key. Ecoprint Mode The Ecoprint enables you to reduce the amount of toner consumed on the page so as to save your printing costs. Ecoprint is Off (default) Ecoprint is On Note The Ecoprint setting has no effect on the print speed. Selecting Ecoprint Mode 1. Press the + or ­ key to display >Ecoprint mode and then press the ENTER key. If you want to change the setting, press the CANCEL key before pressing the ENTER key. The Ecoprint mode setting is now changed. 2-34 Chapter 2 Operating the Laser Printer 2. 11. Resource Protection When you switch from the HP LaserJet 5M emulation to another, all downloaded fonts and macros are lost. [. . . ] 1-6, 4-3 INDEX-3 Mode Select Menu Ready PAR 600 A4 001 >Parallel I/F Nibble (high) Auto High Speed Normal >Baud rate 9600 >Data bits 8 >Stop bits 1 >Parity None >Protocol DTR (pos. )&XON >Barcode mode Off >NetWare Off On >TCP/IP Off On >Ether Talk Off Number of copies 001 >Opt. StatusPage Off >>NetWare Frame Auto >>DHCP OFF >>IP Address These items willl not show unless the printer is installed with the applicable option unit/kit. > Interface Parallel Serial Option 1 Option 2 Basic Operations During Mode Selection This diagram gives quick reference to all menu options and their sequence of selection. Use this description in combination with Chapter 2 Mode Selection Menu. 1. Press the + or ­ key repeatedly until the message display indicates the desired item. [. . . ]