User manual KYOCERA FS-6020

[. . . ] FS-6020 Page Printer Operation Guide Please read the Operation Guide before using the printer. The sections of this guide and parts of the printer marked with symbols are safety warnings meant to protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the printer. WARNING: Indicates that serious injury or even death may result from insufficient attention to or incorrect compliance with the related points. CAUTION: Indicates that personal injury or mechanical damage may result from insufficient attention to or incorrect compliance with the related points. [. . . ] Press the ENTER key. 8 Press the or key to increase or decrease, respectively, the value at the blinking cursor. You can change the maximum space from 0 to 9999 (megabytes). 9 1-41 Chapter 1 Using the Operator Panel 10 Press the MENU key. The message display returns to Ready. Maximum Space Assigned to Virtual Mailboxes (VMBs) This changes the hard disk space for virtual mailboxes. For example, the default size is 50 MB for 340 MB hard disk and 150 MB for 1 GB hard disk. The actual maximum size depends on the size of free hard disk space, however. 1 2 Press the MENU key. Press the or key until e-MPS > appears. e-MPS > 3 4 Press the key. Press the or key and select >e-MPS Configuration >. >e-MPS Configuration > 5 6 Press the key. Press the or key and select >>VMB Size. >>VMB Size 0150MB 7 To change the maximum size, press the ENTER key. The message display shows a blinking cursor (_). >>VMB Size 0150MB 8 Press the or key to increase or decrease, respectively, the value at the blinking cursor. Press the MENU key to exit the menu selection. 9 10 1-42 Chapter 1 Using the Operator Panel Interfaces The printer is equipped with both a parallel and USB interfaces. Option serial interface board kit and network interface card can also be installed. Various printing environment parameters such as the default emulation can be changed independently on different interfaces by using the printer's menu selection system. Select the interface to apply the changes in the procedure described below. NOTE This interface selection described below does not select which interface data will be received from. The printer automatically selects an interface data to be received. 7 Press the or key to display the desired mode. Auto (default) Normal High speed Nibble (high) 8 Press the MENU key. The message display returns to Ready. Changing Serial Interface Parameters NOTE Changing Parallel Interface Modes The parallel interface mode of this printer supports a bi-directional/high-speed mode. After setting the interface, be sure to reset the printer or turn the power off at least once. The new setting will be enabled thereafter. This section applies to the printers having the option serial interface board kit (IB-11) installed. The baud rate, data bits, stop bits, parity, and protocol for the serial interface can be set as follows: 1 2 Press the MENU key. 1 2 Press the MENU key. Press the or key repeatedly until Interface > appears. One of the interface names shown below appears, indicating the current interface. Parallel (default) USB Serial (when a serial interface board kit is installed) Option (only when an optional network interface card is installed) Press the or key repeatedly until Interface > appears. One of the interface names shown below appears, indicating the current interface. Parallel (default) USB Serial (when a serial interface board kit is installed) Option (when a network interface card is installed) 3 Press the ENTER key. Parallel If you want to abandon the interface selection procedure, press the CANCEL key. Parallel > If Parallel is not displayed, press the repeatedly until Parallel appears. or key 4 Press the pears. or key repeatedly until Serial ap- 4 5 6 Press the ENTER key again. Interface ? [. . . ] KIR (Kyocera Image Refinement) This is Kyocera Mita's original smoothing function. It uses software to enhance the printer's resolution and produce high-quality printing. The default setting is On. Kyocera Mita Digital Library This is contained on the CD-ROM supplied with the printer. The contents of the CD-ROM include manuals, printer drivers, and various utilities. [. . . ]