User manual KYOCERA FS-3800

[. . . ] Table of Contents FS-1800/N FS-3800/N Page Printers User's Manual Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The emulation mode can be changed by following the procedures described in Chapter 1. Notice The information in this manual is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. [. . . ] A blinking cursor ( _ ) appears. >Sleep Timer 015 min. 6 Press the or key to increase or decrease the value of the figure where the cursor is blinking and set the desired time. If you want to abandon the setting procedure, press the CANCEL key. 7 ENTER Press the ENTER key. 8 MENU Press the MENU key. The message display returns to Ready. 1-118 Using the Operator Panel Turning Off the Sleep Timer You can turn off the sleep timer function by following the procedure given below. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Sleep Timer > appears. >Sleep Timer > 015 min. 5 ? Press the > key and display >>Sleep Mode. >>Sleep Mode On 6 ENTER Press the ENTER key. On 1-119 Using the Operator Panel 7 Select Off using the or key. >>Sleep Mode ?Off If you want to abandon the setting procedure, press the CANCEL key. 8 ENTER Press the ENTER key. 9 MENU Press the MENU key. The message display returns to Ready. 1-120 Using the Operator Panel >Print HEX-DUMP Received Data Dumping It is possible to print data received by the printer as hexadecimal code for the purposes of debugging programs and files. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the appears. or key repeatedly until > Print HEX-DUMP >Print HEX-DUMP 5 ENTER Press the ENTER key. A question mark (?) appears. >Print HEX-DUMP? 1-121 Using the Operator Panel 6 ENTER Press the ENTER key again. Processing appears for a second, and then Waiting appears. >Processing >Waiting 7 GO Send data to be dumped to the printer. Once the dumped data you require has been output, it is possible to cancel the printing of any further dumped data by taking the printer offline by pressing the GO key and then pressing the CANCEL key. 8 GO Once all data has been received, the message Waiting will appear. Press the GO key to finish printing. 1-122 Using the Operator Panel >Printer Reset Printer Resetting The procedure described below resets the printer's temporary conditions, such as the current unit of measurement, page orientation, font, character code set, margins, etc. , set by commands to their default values. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Printer Reset appears. >Printer Reset 5 ENTER Press the ENTER key. A question mark (?) appears. >Printer Reset ? If you want to abandon the printer resetting procedure, press the CANCEL key 6 ENTER Press the ENTER key again. Self test appears while the printer is resetting itself, then Please wait followed by Ready. Self test Please wait >Ready 1-123 Using the Operator Panel >Resouce Prot. Resource Protection When you switch from the PCL 6 emulation to another, all downloaded fonts and macros are lost. Resource protection preserves these PCL resources in memory so that they are intact when you change the emulation back to PCL 6. Resource protection requires extra memory to store the downloaded fonts and macros. The total size of the printer memory recommended for using the resource protection option is affected by several factors. See Appendix B. Note 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Resouce Prot appears. >Resouce Prot. Off 1-124 Using the Operator Panel 6 Press the or key to display the desired mode. Off (default) Permanent Perm / Temp 7 ENTER When the desired mode is displayed, press the ENTER key. 8 MENU Press the MENU key. The message display returns to Ready. 1-125 Using the Operator Panel >Buzzer Alarm (Buzzer) Setting In addition to the message displayed when the paper supply is exhausted, or when paper jamming occurs, an audio warning is made to sound. This is useful, for example, when the printer is in a location some distance from the user. If the alarm is set to Off, it is made not to sound. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until Buzzer appears. >Buzzer On 5 ENTER Press the ENTER key. On 6 Select On or Off using the or key. 7 ENTER Press the ENTER key. 8 MENU Press the MENU key. [. . . ] In the following example, the print job will be sent to tray numbers 1, 10 to 20, 25, and 30. 9 Press the OK button. To print, use the Print VMB Data menu in the e-MPS menu at the printer operator panel and specify the virtual mail box numbers. For details, see page 1-29 in the User's Manual. 3-22 Printing through Application Software 3. 4. 3 Printing with Job Storage Using Job Storage, you can print multiple copies by sending the data for just one copy (electronic sorting), or print jobs stored on the Microdrive at any time as required using the option barcode reader. Electronic Sorting The electronic sorting function allows you to print multiple copies of a document while only requiring the data to be transferred to the printer once. This approach reduces the amount of time that it takes to print multiple copies. [. . . ]