User manual KYOCERA FS-3700+

[. . . ] Table of Contents FS-1700 FS-3700 User's Manual Kyocera Laser Printer Introduction Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The printer is factory-set to emulate the HP LaserJet 5M (excluding support for paper sizes larger than A4/letter). The emulation mode can be changed by following the procedures described in Chapter 2. [. . . ] The following items can be selected by using the MODE, + and -, and ENTER keys. Also, the diagram on the last page in this manual gives a quick reference to the full options and the sequence of selection. Mode Select Menu Item , Function Selects the interface on which the control panel settings are effective. Parallel setting has a sub item in which one of four data transmission modes can be selected -- . ""/0 01, , . , or ) 0  Serial setting has five sub items, and sets the following RS-232C/RS-422A parameters: Baud rate Data bits Stop bits Parity Protocol If an optional network board is installed, also makes the network settings. Default Setting Parallel Nibble (high) 9600 8 1 None DTR(pos. )&XON . " $ - 001 HP LaserJet 5M - Bitmap Selects the bitmap or scalable font for the current interface. Sub items allow selection of typefaces and scaling of the scalable font. For example, you can select one of the Courier fonts as the default font for printing. The + and - keys toggle between portrait and landscape page orientations. Portrait 2 * *$*3 - Reads information from the option ROM installed in -- the printer's main board. Reads or writes data from or to an memory card in the printer's memory card slot. Also, this menu allows deletion of data from an memory card; and formatting the memory card. Using the Mode Select Menu Item *  - Function Default Setting Selects the multi-purpose tray mode from first, cas- First sette, or manual. The key allows access to submenu -* A4 or Letter 4, selects the size of multi-purpose tray. DL or Business $5 4 #6  4 Selects the size of paper for the optional bulk paper A4 or Letter feeder. Selects the paper type for printing -- Normal (60-90 Normal g/m2) or Thick (90-200 g/m2). We recommned that is fed from the Multi-purpose tray and printed paper output to the Face-up tray. Selects the binding mode for duplex printing-- short-edge or long-edge binding. Selects the sorter mode from stacker, collator, sorter, and mail box modes. None Stacker 7   Selects one of the automatic paper cassette switch- None ing modes. Only available when the printer is installed with the optional paper feeder (PF-20/ PF-20mini). By pressing the (FORM FEED) key and + and - keys, -- the following settings can be made: Message language; formfeed time-out, sleep timer time-out; printing in hexadecimal dump mode; printing a list of resident fonts; resetting the printer; linefeed and carriage return action; panel keep mode; display of total pages printed; KIR optimization; Ecoprint mode; resource protection mode; printing resolution optimization; print density; buzzer; other service menu settings. 0 - : These items are available only when the printer is installed with the applicable option unit/kit. For items with the mark on the message display, the (FORM FEED) key lets you go down to the sub items which give access to more items to change the relevant settings. 2-13 2. 4. Sleep (Ecopower) Mode The printer has a sleep timer to conserve power when the printer is not printing, processing, or receiving data. You can adjust the timer value, the length of time the printer waits before entering sleeping mode in the absence of data. [. . . ] RS-232C Cable Connection If you are uncertain as to the printer's current parameter settings, you can reset them to the values listed above by following the manner described in the last page in this manual. On many computers this can be done by setting DIP switches before power is turned on. Another method is as follows: In DOS, enter the following commands: C:\>MODE C:\>MODE COM1:96, N, 8, 1, P LPT1:=COM1 To test the interface, then enter: CTRL P C:\>DIR CTRL P The software settings made by the procedures above are temporary. If you want to use a different baud rate or change any of the other RS-232C parameters, you can use the printer's FRPO (firmware reprogram) command. [. . . ]