User manual KYOCERA FS-3600

[. . . ] No responsibility is assumed for defects in the printer's firmware (contents of its read-only memory). This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. Copying or other reproduction of all or part of this manual, any copyrightable subject matter without the prior written consent of Kyocera Corporation is prohibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copyright notice as the material from which the copying is done. Regarding Tradenames PRESCRIBE is a registered trademark of Kyocera Corporation. [. . . ] If you wait awhile, ý)RUP)HHGý7LPH2XW will be displayed and the last page will be printed automatically. Pressing the FORM FEED key allows you to finish printing immediately. 1. The message display will now readý3URFHVVLQJ and the last page will print. Theý:DLWLQJ display may also appear due to interruptions in printed data while the computer is processing data. Pressing the FORM FEED key unnecessarily when the message display reads :DLWLQJ will result in a form feed. 2-10 2. 3. Using the Mode Select Menu 2. 3. Using the Mode Select Menu This section explains how to use the MODE key on the control panel. The MODE key allows you to set or change the printer environment such as the number of copies to make, emulation, page orientation, code set, etc. The following items can be selected by using the MODE, + and ­, and ENTER keys. Also, the diagram on the last page in this manual gives a quick reference to the full options and the sequence of selection. Mode Select Menu Item 3ULQW ý 0HQXý 0DS , QWHUIDFHý ý ý ý ý ý !Selects the interface on which the control panel settings are effective. Parallel setting has a sub item in which one of four data transmission modes can be selected -- 1LEEOHýõKLJKô, $XWR, 1RUPDO, or +LJK VSHHG Serial setting has five sub items, and sets the following RS-232C/RS-422A parameters: Baud rate Data bits Stop bits Parity Protocol If an optional network board is installed, also makes the network settings. Also with KPDL emulation, print settings can be made when there is an error or alternative emulation. (This cuts down the total time of printing. ) Note however that data written to the RAM DISK is lost if the power to the printer is turned off or the printer is reset. RAM DISK settings can be made from the printer's control panel. The RAM DISK is set from the printer's user memory. The printer's printing speed may therefore drop or insufficient memory errors result depending on the value of the RAM DISK setting. Setting the RAM DISK Size 1. Press the + or ­ key and selectý5$0ý', 6. ýPRGHý!. Press the + or ­ keys to displayý2Q and then press the ENTER key. 4. Press the ENTER key again, and change the RAM DISK size using the + or ­key. It is not possible to make a setting that exceeds total printer memory. The default value for the RAM DISK is the total printer memory minus 9 MB. This parameter may be set anywhere fromýíì toýçê depending on the available printer memory. The setting will be activated after restart. RAM DISK Operations The following operations are available with the RAM DISK. Ì Ì Ì Ì Read Data Write Data Delete Data Print a List of Data Names Procedures for all operations are the same as for a memory card. [. . . ] ý . 3'/ ý ý !&RGHý VHW ý , 62ðçý $6&, , !3ULQWý . 3'/ý HUUV ý ý !3ULQWý . 3'/ý HUUV 2II ý 2Q !$OWïý (PXODWLRQ ý 3&/ý ç !3ULQWý . 3'/ý HUUV ý ý !3ULQWý . 3'/ý HUUV 2II ý 2Q ý ý ý ý (*1) (*2) (PXODWLRQý ý ý ý ý ý ý ý !ý . 3'/ý õ$872ô ý (*2) (PXODWLRQý ý ý ý ý ý ý ý !ý ý (PXODWLRQ , %0ý 3URSULQWHU ý /LQHý 3ULQWHU (PXODWLRQý ý ý ý ý ý ý ý !ý ', $%/2ý çêí (PXODWLRQý ý ý ý ý ý ý ý ! [. . . ]