User manual KYOCERA FS-1800

[. . . ] Table of Contents FS-1800 Page Printer Operation Guide Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The emulation mode can be changed by following the procedures described in Chapter 1. Notice The information in this guide is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this guide. [. . . ] You can adjust the timer value, the length of time the printer waits before entering sleeping mode in the absence of data. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Sleep Timer > appears. The default setting is 015 min. >Sleep Timer > 015 min. 5 ENTER Press the ENTER key. A blinking cursor ( _ ) appears. >Sleep Timer 015 min. 6 Press the or key to increase or decrease the value of the figure where the cursor is blinking and set the desired time. If you want to abandon the setting procedure, press the CANCEL key. 7 ENTER Press the ENTER key. 8 MENU Press the MENU key. The message display returns to Ready. 1-122 Using the Operator Panel Turning Off the Sleep Timer You can turn off the sleep timer function by following the procedure given below. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Sleep Timer > appears. >Sleep Timer > 015 min. 5 ? Press the > key and display >>Sleep Mode. >>Sleep Mode On 6 ENTER Press the ENTER key. On 1-123 Using the Operator Panel 7 Select Off using the or key. >>Sleep Mode ?Off If you want to abandon the setting procedure, press the CANCEL key. 8 ENTER Press the ENTER key. 9 MENU Press the MENU key. The message display returns to Ready. 1-124 Using the Operator Panel >Print HEX-DUMP Received Data Dumping It is possible to print data received by the printer as hexadecimal code for the purposes of debugging programs and files. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the appears. or key repeatedly until > Print HEX-DUMP >Print HEX-DUMP 5 ENTER Press the ENTER key. A question mark (?) appears. >Print HEX-DUMP? 1-125 Using the Operator Panel 6 ENTER Press the ENTER key again. Processing appears for a second, and then Waiting appears. Processing Waiting 7 GO Send data to be dumped to the printer. Once the dumped data you require has been output, it is possible to cancel the printing of any further dumped data by taking the printer offline by pressing the GO key and then pressing the CANCEL key. 8 GO Once all data has been received, the message Waiting will appear. Press the GO key to finish printing. 1-126 Using the Operator Panel >Printer Reset Printer Resetting The procedure described below resets the printer's temporary conditions, such as the current unit of measurement, page orientation, font, character code set, margins, etc. , set by commands to their default values. 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Printer Reset appears. >Printer Reset 5 ENTER Press the ENTER key. A question mark (?) appears. >Printer Reset ? If you want to abandon the printer resetting procedure, press the CANCEL key 6 ENTER Press the ENTER key again. Self test appears while the printer is resetting itself, then Please wait followed by Ready. Self test Please wait Ready 1-127 Using the Operator Panel >Resouce Prot. Resource Protection When you switch from the PCL 6 emulation to another, all downloaded fonts and macros are lost. Resource protection preserves these PCL resources in memory so that they are intact when you change the emulation back to PCL 6. Resource protection requires extra memory to store the downloaded fonts and macros. The total size of the printer memory recommended for using the resource protection option is affected by several factors. See Appendix B. Note 1 MENU Press the MENU key. 2 Press the or key repeatedly until Others > appears. Others > 3 ? Press the > key. 4 Press the or key repeatedly until >Resouce Prot appears. >Resouce Prot. Off 1-128 Using the Operator Panel 6 Press the or key to display the desired mode. Off (default) Permanent Perm / Temp 7 ENTER When the desired mode is displayed, press the ENTER key. 8 MENU Press the MENU key. The message display returns to Ready. 1-129 Using the Operator Panel >Buzzer Alarm (Buzzer) Setting In addition to the message displayed when the paper supply is exhausted, or when paper jamming occurs, an audio warning is made to sound. This is useful, for example, when the printer is in a location some distance from the user. [. . . ] The Print dialog box will displayed. 3-33 Printing through Application Software 2 Click on the Name drop down list, all the printers installed under Windows are listed. Click the name of the printer you want to use. 6 2 3 4 5 3 4 5 Select the range of the pages you want to print in the document, All or Current page only in Page range. To print part of the document, enter page numbers separated by commas. Specify the number of pages you want to print in the Number of copies combo box in Copies. [. . . ]