User manual KYOCERA FS-1500

[. . . ] No responsibility is assumed for defects in the printer's firmware (contents of its read-only memory). This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer, are protected by copyright. Copying or other reproduction of all or part of this manual, any copyrightable subject matter without the prior written consent of Kyocera Mita Corporation is prohibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copyright notice as the material from which the copying is done. Regarding Tradenames PRESCRIBE is a registered trademark of Kyocera Corporation. [. . . ] Set paper of the size and type specified in the print data into the MP tray, then press the key to resume printing. When you want to feed from a source other than the MP tray, make sure there is no paper in the MP tray, then press the key to switch the paper source. The printer prints on the paper size set in that particular paper source. For details on how to clear paper jams, see section 3. 4 Paper Jam Removal on page 3-15. Table 3-3 3-7 Indicators Indicator KM-NET for Clients display Paper path error Corrective Action There is no cassette in the feeder, or the cassette is not inserted properly. After reinserting the paper cassette, you should be able to print. Replace toner There is no more toner in the toner container. (See Chapter 2) Set paper Press GO There is no paper in the MP tray. Feeding the paper having a paper size which does not match the current paper size from the MP tray can cause paper jam. Note Toner low There is not enough toner inside the toner container. Promptly replace with a new toner as the printer will stop printing before long. (See Chapter 2) The print job cannot be done at current resolution because there is not enough internal memory. The printer's memory is running low because of the number of downloaded fonts and macros. Print a status page to see how much user memory is left and try deleting unnecessary fonts and macros. The printer will stop whenever paper jams in the printer or paper is not fed from a paper cassette. The printer will go offline and (paper jam) indicator will light in the operator panel. When a jam occurs, check the points indicated in the following and clear the jam as indicated. If paper jams occur frequently, try using a different type of paper, replace with paper from another ream, turn the stack of paper over, or turn the paper the other way around. Also, look for tiny pieces of paper that may have been torn apart and overlooked when the jammed paper was removed. If you cannot solve the problem by changing the paper, there may be a problem with the printer. Torn pieces of paper are difficult to remove and may be easily overlooked, deterring the jam recovery. Depending on where the jam occurred, the printer may or may not reprint the jammed page. Note · 3. 4. 1 Jam at the Face-down Tray and the Rear Cover If paper is not completely ejected and has stopped only part way out, open the rear cover and remove the jammed paper by pulling it out. The printer then automatically warms up and resumes printing. Rear Cover Figure 3-1 3-15 Paper Jam Removal 3. 4. 2 Jam at the Paper Cassette Pull out the paper cassette and remove any partially fed paper, then reclose the paper cassette. Follow the same steps for clearing the jammed paper at the option paper feeder's paper cassette. Paper Feeder Paper Cassette Figure 3-2 Paper Feeder's Paper Cassette 3. 4. 3 Jam at the Duplexer When a paper jam occurs in the duplex section, clear it using the following procedure. 1 Open the rear cover and remove the jammed paper as shown in the figure. Rear Cover Figure 3-3 3-16 Paper Jam Removal 2 Pull the paper cassette all the way out of the printer. Paper Cassette Figure 3-4 3 Open the duplexer's rear cover and remove any jammed paper. Duplexer's Rear Cover Figure 3-5 4 Open the duplexer's front cover and remove any jammed paper. Duplexer's Front Cover Figure 3-6 5 6 Insert the paper cassette into the slot in the printer. The printer then automatically warms up and resumes printing. 3-17 Paper Jam Removal 3. 4. 4 Jam Inside the Printer When a paper jam occurs inside the printer, clear it using the following procedure. 1 Open the printer's top and front covers. [. . . ] The default setting is Off. KM-NET for Clients This is a utility that displays a virtual printer operation panel on your computer screen. You can make various settings from the KM-NET for Clients, such as the current paper source and paper size. The KM-NET for Clients is contained on the Kyocera Mita Software Library CD-ROM supplied with the printer. Emulation This refers to emulation of manufacturers' printers. The printer emulates operation of the following printers: PCL, Line printer, IBM Proprinter, DIABLO 630, EPSON LQ-850, KPDL. KM-NET VIEWER This is a network management tool that can be used with the printer. [. . . ]