User manual KYOCERA FS-1200

[. . . ] Table of Contents FS-1200 User's Manual Kyocera Laser Printer Introduction Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The emulation mode can be changed by following the procedures described in Chapter 2. Notice The information in this manual is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. [. . . ] Selects the interface on which the control panel settings are effective. Parallel setting has a sub item in which one of four data transmission modes can be selected -- 1LEEOHýõKLJKô, $XWR, 1RUPDO, or +LJK VSHHG The following settings can be made from the optional IB-10 serial interface: Baud rate Data bits Stop bits Parity Protocol If an optional network board is installed, also makes the network settings. Also with KPDL emulation, print settings can be made when there is an error or alternative emulation. -- Parallel Default Setting Auto 9600 8 1 None DTR(pos. )&XON (PXODWLRQý ý ý ý ý ý ! PCL 6 )RQWý ý ý ý ý ý ý ý ý ý ý ! Select the current interface font. The default number Internal for selecting an internal font is I000 (this is the num- I000 (Courier) ber for Courier). If there are optional fonts in the printer other than the internal ones, you can specify them by switching to theý2SWLRQ display. Depending on the type of optional font, the symbols used at the start of the font number change as follows: Soft font (Download): S Fonts resident in a Memory Card: M Fonts resident in a RAM disk: H Fonts resident in an optional ROM: O This menu also allows printing the font lists, selecting Courier, Letter Gothic, and selecting the size and pitch of the font. 2-11 2. 3. Using the Mode Select Menu Item 3DJHý VHWý ý ý ý ý ý ý !Number of copies Page orientation Page protect LF action CR action Wide A4 Press the key to set the following print quality. KIR mode Ecoprint mode Resolution Reads information from the option ROM installed in the printer's main board. The following settings can be made from sub-menus when the total printer memory is 12 MB or more and this mode is set to 2Q. Reads or writes data from or to an memory card in the printer's memory card slot. Also, this menu allows deletion of data from an memory card; and formatting the memory card. The following operations can be performed from submenus on paper type. MP tray mode Paper size for MP tray Paper type for MP tray Cassette size for custom sizes Paper type for Cassette 1-3 Duplex printing mode* Optional sorter mode* Override A4/Letter Set up the custom paper type Reset the custom paper type The following sub-menus can be displayed by pressing the key and then the + and ­ key Message language setting Automatic form feed timeout setting Sleep timer setting [See page 2-22. ] Receive data damping [See page 2-23. ] Printer reset Display total number of printed pages Resource setting* Alarm (buzzer) setting Service (for service personnel) Default Setting 001 Portrait Auto LF only CR only Off On Off 600 dpi -- Off 3ULQWý TXDOLW\ý ý ! 2SWïý 520ý ý ý ý ý ý ý !5$0ý ', 6. ý PRGHý ý ! 0(025<ý &$5'ý ý ý ý ! -- 3DSHUý KDQGOLQJý ! First A4 or Letter Plain 216 mm × 356 mm Plain None Stacker Off -- -- 2WKHUVý ý ý ý ý ý ý ý ý ! English 30 sec. -- -- -- Off On -- / *: These items are available only when the printer is installed with the applicable option unit/kit. mark on the message display, the (FORM FEED) key lets you go down to the sub items which give access to more items to change the relevant settings. 2-12 2. 4. Configuring Interfaces 2. 4. Configuring Interfaces The printer is equipped with a parallel interface. To configure each interface, press the MODE key and use the + or ­ key to select the interface you wish to make settings for. This interface selection does not select which interface data will be received from. The printer automatically selects that interface. Parallel Interface The parallel interface mode of this printer supports a bi-directional/high-speed mode. Normally, this interface is used under the default settingý $XWR, see Appendix C. [. . . ] ý . 3'/ý õ$872ô ý (*2) (PXODWLRQý ý ý ý ý ý ý ý !ý ý (PXODWLRQ , %0ý 3URSULQWHU ý /LQHý 3ULQWHU (PXODWLRQý ý ý ý ý ý ý ý !ý ', $%/2ý çêí (PXODWLRQý ý ý ý ý ý ý ý !ý (3621ý /4ðåèí ý ý ý !&RGHý VHW ý , %0ý 86 ý !&RGHý VHW ý ', $%/2ý 86 !&RGHý VHW ý /4ý 86 ý ý ý Continued on next page Continued from Previous page ý )RQWý ý ý ý ý ý ý ý ý ý ý ý ý ! [. . . ]