User manual KYOCERA FS-1020D

[. . . ] FS-1020D Page Printer Operation Guide Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The emulation mode can be changed by following the procedures described in Chapter 1 . Notice The information in this manual is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. [. . . ] Contact your Kyocera Mita dealer. (No indication patterns available) Warning image adapt (No indication patterns available) Warning low memory Warning waste toner box Table 3-3 (Continued) 3-8 Indicators 3. 3. 2 Errors Requiring Service Personnel Attention When the following errors occur, turn off your printer, remove the plug from the AC outlet, and contact your Kyocera Mita dealer. The indicators are shown in two different states, according to the way they alternate. Indicator Corrective Action Main motor error (2000error) Contact your Kyocera Mita dealer. Scanner motor error (4000 error) Contact your Kyocera Mita dealer. Scanner pin-photo error (4200 error) Contact your Kyocera Mita dealer. Eraser error (5300 error) Contact your Kyocera Mita dealer. Table 3-4 3-9 Indicators Indicator Corrective Action Fuser error (6000 error) Contact your Kyocera Mita dealer. The waste toner reservoir is full (7980 error) Turn off the printer's power and remove the process unit from the printer. Gently shake the process unit horizontally a few times, then reinstall it into the printer. If this error message does not disappear, contact your Kyocera Mita dealer (less than 100, 000 pages printing). The waste toner reservoir is full (7990 error) Same as above (100, 000 pages printing or more). Controller check sum error (F010 error) Contact your Kyocera Mita dealer. Controller RAM read/write error (F020 error) Contact your Kyocera Mita dealer. Table 3-4 (Continued) 3-10 Indicators Indicator Corrective Action Controller system error (F030 error) Contact your Kyocera Mita dealer. Communication error (F040 error) Contact your Kyocera Mita dealer. Engine ROM check sum error (F050 error) Contact your Kyocera Mita dealer. Table 3-4 (Continued) 3-11 Indicators 3. 3. 3 Error Messages With the following errors, printing continues when you press the printer's key. (See pages 1-4 and 1-5. ) Indicator KM-NET for Clients display File not found Press GO Corrective Action The specified file is not found. An error has occurred during access to the memory card using the PRESCRIBE RWER command or from the KMNET for Clients. Look at the error code given in place of ## and refer to the corresponding description given below. The data transferred to the printer was too complex to print on a page. To release the page protect mode, send the following command to the printer from the KM-NET for Clients after this error occurs: !R!FRPO R5, 1; EXIT; KPDL Error Press GO MemoryCard err## Press GO Memory overflow Press GO Print overrun Press GO Note RAM DISK error ## Press GO Check the error code displayed in ## and refer to the appropriate description below. Expand printer memory. Table 3-5 3-12 Indicators Indicator KM-NET for Clients display None Corrective Action The printer has halted because you attempted to insert/ remove a memory card into/from the printer slot while the printer power is on. Make sure to turn the printer power off before inserting/ removing a memory card. Note None Format error Memory card This message appears when the printer is in the ready state and the memory card is not formatted, and therefore cannot be read or written. Format the memory card. Table 3-5 (Continued) 3-13 Indicators 3. 3. 4 Normal Indicator Display The following displays appear during normal printer operation. Indicator KM-NET for Clients display Cancelling data Description Data inside the printer is being canceled. The indicators light in sequence from the top, then go off in sequence from the bottom. When the printer is switched on for the first time after the toner container is installed, (Adding toner) also appears. When the printer is switched on for the first time after the toner container is installed, (Adding toner) also appears. Please wait Processing The printer is receiving data. Processing Waiting The printer is processing data. The printer is waiting for the end-of-job command before printing the last page. The printer is ready to print. Form Feed Timeout Ready The printer is offline. The indicator flashes at 5-second intervals and all other indicators go off. The printer wakes from Sleep mode whenever a key on the operator panel is pressed, the cover is opened or closed, or data is received. (You can set the amount of time before the printer enters sleep mode from the KM-NET for Clients utility. ) Table 3-6 3-14 Paper Jam Removal 3. 4 Paper Jam Removal This section describes how to remove paper when it jams in the printer. The printer will stop whenever paper jams in the printer or paper is not fed from a paper cassette. [. . . ] You can view information for printers connected to the network using SNMP commands. KM-NET VIEWER is contained on the Kyocera Mita Software Library CD-ROM supplied with the printer. Expansion memory This option is used to increase printer memory. The printer has one expansion slot, and you can install a 8 MB, 16 MB, 32 MB, 64 MB, 128 MB, or 256 MB DIMM (Dual Inline Memory Module). Contact your Kyocera Mita dealer to purchase the DIMM that is best suited for use with this printer. KPDL (Kyocera Printer Description Language) This is Kyocera Mita's version of Adobe PostScript 3. First mode This is an operation mode for the MP tray. [. . . ]