User manual KYOCERA FS-1000

[. . . ] Table of Contents Page Printer User's Manual Caution NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The emulation mode can be changed by following the procedures described in Chapter 1. Notice The information in this manual is subject to change without notification. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this manual. [. . . ] The total host buffer size can be between 5 kB and the printer's free memory size. 1 Click the MENU button on the start-up screen. 2 The Menu dialog box is displayed. Using the radio buttons on the right, select either Fix or Auto. Memory Host buffer mode 1-45 Other Settings 3 Click Host buffer size. The total host buffer size is increased or decreased in 1 kB increments. You can input the host buffer size directly in the number field. Host buffer size 4 Note Turn the printer's power off and on again. The setting becomes effective when you restart the printer. We recommend that you leave the default settings for Host buffer mode and Host buffer size unchanged. 1-46 Other Settings 1. 6. 5 Adding a Name and Description to the Printer You can add a name, asset number, and description to the printer. The asset number can only be defined when your printer is connected to a network, and is stored by the printer. The name and explanation are stored in the Remote Operation Panel utility. 1 Click the MENU button on the start-up screen. 2 The Menu dialog box appears. Double click on General and then on User defined setting. General User defined setting 3 Click the item you want to set, and enter the text for that item in the text box on the right side of the screen. The example below shows the screen that appears when you click on Nickname. Type in the name of the printer. Nickname 4 After making the settings, click the OK button to return to the startup screen. The settings are changed. 1-47 Other Settings 1. 6. 6 Displaying the Resource List When the printer is connected to a network, you can display the printer's resource list, including fonts, programs, macros, and/or host data. 1 Click the Resource tab. Resource tab 2 Click the check box that corresponds to the resource you want to display. Font check box 3 Click the Update button. A list of all items for that resource are displayed. Update 4 After confirming, click the OK button to return to the start-up screen. 1-48 Other Settings 1. 6. 7 Sending PRESCRIBE Commands to the Printer You can send commands to the printer in Kyocera Mita's PRESCRIBE printer language by broadcasting. You can also use this menu to confirm the printer's internal settings. For details on PRESCRIBE commands and FRPO settings, refer to the Programming Manual provided on the CD-ROM supplied with the printer. Note 1 Click the MENU button on the start-up screen. 2 The Menu dialog box appears. Click Broadcast. Broadcast 1-49 Other Settings 3 Click Broadcast to display the dialog box shown below. Broadcast FRPO Broadcast To send PRESCRIBE commands to the printer, enter the command in the Broadcast text box. FRPO FRPO is a PRESCRIBE command that permanently changes the printer's internal parameters. Each parameter is represented by two letters, such as R4 for default paper source, succeeded by FRPO, then followed by a value. For example, FRPO R4, 1; means that the default paper source (R4) is the printer's cassette (1). To confirm the current value for an FRPO parameter: 1 2 1 2 3 Enter the parameter (for example R4) in FRPO. The current value is shown in Value. To change the value for an FRPO parameter: Follow the above procedure to display the current value in Value. For example, to change the default paper source to the MP Tray in the above example, enter 0 instead of 1 in Value. The value is changed. 1-50 Chapter 2 Printer Driver 2 This chapter describes how to perform basic print operations using the printer driver, such as setting the paper size and selecting a paper source. [. . . ] To use this, the KPDL2 Upgrade Kit (PK-6) must be installed on your printer. Kyocera Mita Digital Library This is contained on the CD-ROM supplied with the printer. The contents of the CD-ROM include manuals, printer drivers, and various utilities. Face-up tray This is located at the rear of the printer. Select paper output to the face-up tray when printing on postcards, envelopes, or labels. Kyocera Mita PrintMonitor This is a network management tool that can be used with the Kyocera FS series. You can view information for printers connected to the network using SNMP commands. [. . . ]