User manual KRUPS FNP1

[. . . ] -To disconnect, turn switch to "OFF", then remove plug from wall outlet. -Use extreme caution when dispensing hot steam. SAVE THESE INSTRUCTIONS 6 KRUPS - -- -- -- - - -- - - -- - - -- - - ---- -- CAUTION -This appliance is for household use only. Any servicing other than routine cleaning and user maintenance should be performed by authorized KRUPSservice personnel only (see Guarantee of Performance). -To reduce the risk of fire or electric shock, do not remove the base of the machine. [. . . ] Turn the function selector (b) to the position «~» and allow all the water contained in the tank to run through the machine. f necessary, interrupt this operation by turning the function selector (b) to the position 0 to empty the container then resume the operation Using the vario] your espresso. : . , tions of . Forbestr . Fi 1. ESPRESSOFUNCTION esults, preheat the accessories (filter holder, filter and cups) by running water directly into the cups (see «Before first use»). Whenthecuparefull of hotwater, reset . Sett . Putt . Putsomeground ll the water container with fresh, cold water (1) he «on/off» switch (h) The indicator light (h1) will come on. he filter for one cup in the filter holder . Fi . Sett . Movet . Pl . Thent Please note: the sliding part (g2) of the nozzle must be in the down position (5) ll the water container with fresh, cold water (1). As soon as the appliance reaches the correct temperature, the indicator light (c) comes on. the cups are full, reset the function selector (b) to the position O. . Cl . Putt . Pl . Thent . When coffee in the filter, firmly pressing down the ground coffee with the back of the spoon (1 measuring spoon = 1 cup) (3) eanthe edgesof the filter holder. he filter holder in place (2) aceone espressocup under the filter holder. he «on/off» switch (h). As soon as the appliance reaches the appropriate temperature, the temperature control indicator light (c) will come on. Return the nozzle to the inside and hold the container by its handle or place it on the grid (I) (6) urn the function selector (b) to the position «6» until to obtain some steam then reset it to the position 0 and remove the container mmerse the tip of the nozzle in the milk to be heated. Return the nozzle to the inside and hold the container by its handle or place it on the grid (i) (6) KRUPS 9 . I As soon as the appliance reaches the appropriate temperature, the temperature control indicator light (c) will come on. turn the function selector (b) to the . Then . Do . position «\!!\. J» until the milkis frothed enough, then reset it to the pOSItion 0 and remove the container. the cleaning operation In order to prevent the nozzle from becoming blocked: place an empty container under the nozzle. then turn the function selector (b) to . the position «\!!\. J» again during few seconds. operation in order to prevent the nozzle from becoming blocked: place an empty container under the nozzle. then turn the function selector (b) to the position «\!!\. J» again during few seconds. clean the nozzle with a damp cloth. thorough cleaning of the nozzle, please turn the functionselector(b)to the position O. horough cleaning of the nozzle, please refer to the paragraph «Maintenance». refer to the paragraph «Maintenance». Notes If you wish to make an espresso immediately after steam, the appliance must first cool down until it reaches the right temperature for extraction . Fort . Fi . Set . Pl . Todo . Lett . Heating water (for tea, for example) or thick liquids (soup, for example) Please note: the sliding part (g2) of the nozzle must be in the raised position (5). llthe water container with fresh, cold this, insert an empty filter holder (no coffee) in the machine and pOSItion a suitable container beneath it. he water run through until the indicator water (1) the «on/off» switch (h) The indicator light (h 1) comes on. As soon as the appliance reaches the appropriate temperature, the temperature control indicator light (c)willcome on. ace an empty container under the nozzle. Return the nozzle to the Inside and hold the container by its handle or place it on the grid (i) (6) turn the function selector (b) to the . Move light (c) goes out. Then, turn the function selector (b) to the position 0 After this, the machine is now ready once more to make an espresso (see paragraph «espresso function»). Please note: when the appliance is running, and also afterwards, the nozzle will be very hot. [. . . ] This warranty will be void if malfunction was caused by damage to the product by accident, misuse, use on frequency or voltage other than marked on the product and/or described in the instructions, abuse including tampering, damage in transit, or use for commercial purposes. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. KRUPS 13 --- - --- - - -u-u -- ---- GUARANTEE OF PERFORMANCE This fine KRUPS product is manufactured according to a rigid code of quality standards, and, with minimum care, should give years of service. However, should the need arise for repairs or for replacement parts within or after the warranty period, please call our CONSUMER SERVICEDEPARTMENT: USA: (800) 526-5377 24-hours a day, 7 days a week (905) 669-0114 Monday-Friday 8:00 a. m - 4:30 p. m Canada: You will be provided with specific instruction on how to get your product repaired. The department will also be able to answer any general product questions you may have. [. . . ]