User manual KORG X5

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. [. . . ] Note: MIDI program changes only work for Timbres whose Status is set to INT. 2. Use the ClickPoint to highlight "Program Select, " and use the [VALUE] dial etc. · "Selecting programs from the front panel:" (p. 37) · When selecting by category, "Selecting programs by category" will be the only available method. (p. 38 "Selecting programs by category") Adjusting a timbre's pan and volume Adjusting the pan (stereo position) Here's how to adjust the pan of each timbre. This page shows the pan and volume settings for the programs assigned to timbres 1­8. 2. Use the ClickPoint [][®][][] to highlight the "Pan" of the timbre whose pan setting you 60 REALTIME CONTROLS [1], [2], [3], [4], [SELECT] Quick Start A setting of C064 is center, L001 is far left, and R127 is far right. With a setting of RND, the stereo location will change randomly between left and right each time a note is played. Once you've tweaked the sound to perfection, you'll want to save your work. Use the ClickPoint to select "Write Combination, " and then press the ClickPoint center. Adjusting the volume Here's how to adjust the volume of each timbre. Use the ClickPoint [][®][][] to highlight the "Volume" of the timbre whose volume setting you want to adjust, and use the [VALUE] dial etc. to adjust the setting. The Write Combination dialog box will appear. Program Adjusting the volume while preserving the volume balance between timbres 1. Press the [UTILITY] button to access the utility menu. Note: If the display indicates "Memory Protected, " the combination memory protect is turned on. There is one insert effect and two master effects, and for each of these you can choose one of 89 effect types. Note: The effect settings created and saved with a program in Program mode are not used in Combination mode. Effect settings are made independently for the combination. Overview of Combi mode parameters Select a program for each timbre In the COMBI 0: Play, Prog page (or COMBI 1: Ed­ Tone Adjust, Prog page), select a program for each timbre. Status and MIDI settings In the COMBI 2: Ed­Track Param, MIDI page, set "Status" to INT for the timbres that you want to play, and set their MIDI channel to the global MIDI channel. Arpeggiator A combination can use two arpeggiators (dual polyphonic arpeggiators). You can select the arpeggio pattern, specify the range in which the arpeggio is generated, and specify the region of notes (keys) or velocities that will trigger the arpeggiator. Combination structure and corresponding pages Controller Setup : 7-5 Timbre1 Program Parameters Arpeggiator: 7-1. . . 4 Insert Effect : 8-1 Master Effect 1, 2 : 9-1. . . 3 Timbre Insert Effect : 8-2, 3 Timbre2 Parameters Program Timbre3 Program Timbre4 Program Parameters MasterEQ :9-4 Parameters Insert Effect Master Effect Individual Outputs Parameters AUDIO OUTPUT L/MONO, R AUDIO OUTPUT INDIVIDUAL 1, 2 Timbre8 Program 1­1, 9­4, etc. indicate the X5 on-screen pages and tabs. 62 Selecting a program for each timbre Quick Start Overview of editing pages In the COMBI 0: Play page you can select and play combinations, select the program used by each timbre, adjust the mixing, and adjust the arpeggiator setting. The other pages let you modify the sound in more detailed ways. · Select and play combinations. · Select a program for each timbre, and set status, pan, and level. (Same as the 1: Ed­ Tone Adjust parameters; can be edited from either page. ) · Select an arpeggio pattern and make settings. · Select a program for each timbre, and set status, pan, and level. · MIDI message transmission/reception filter settings for each timbre. (Same as the 0: Play parameters; can be edited from either page. ) · Controller settings. [. . . ] Delete the "Unknown device" entry, and reinstall the driver. p. 28 MIDI, USB This instrument does not respond to incoming MIDI data Are all MIDI cables connected correctly?p. 31, 34 Is the MIDI data being received on the channel on which it is being transmitted?PG p. 81 This instrument does not respond correctly to incoming MIDI data Are the GLOBAL 1: MIDI page MIDI Filter settings "Enable Program Change, " "Bank, " "Combi, " "Ctrl Change, " "AfterT, " and "Exelusire" each checked? [. . . ]