User manual KORG TRIDENT MKII SERVICE MANUAL

[. . . ] Steps in a procedure are listed as 1 2 3 . . . p. s, BG p. s, s. s ­ s From the left, these symbols indicate a reference page in the Parameter Guide, a reference page in the Basic Guide, and a parameter number. Conventions in this manual Abbreviations for the manuals BG, PG, VNL References to the manuals included with the TRITON-Rack are abbreviated as follows. BG: Basic Guide PG: Parameter Guide VNL: Voice Name List Switches and knobs [ ] References to the keys, dials, and knobs on the TRITONRack's panel are enclosed in square brackets [ ]. References to buttons or tabs indicate objects in the LCD display screen. Parameters in the LCD display screen " " Parameters displayed in the LCD screen are enclosed in double quotation marks " ". Symbols , , , , , These symbols respectively indicate cautions, advice, MIDIrelated explanations, a parameter that can be selected as an alternate modulation source, a parameter that can be selected as a dynamic modulation source, and a parameter that can use the BPM/MIDI Sync function. [. . . ] Keys that are set to 0 will sound at the amp level of the program that uses this drum kit. Keys that are set to ­99 will not sound. 5. 1­1a 5. 1­1b Vel. SW LH (Velocity SW LoHi) [001. . . 127] 5. 1­1c 5. 1­1d Specifies the velocity value at which you will switch from the Low drumsample to the High drumsample. Velocities above this value will sound the High drumsample, and velocities below this value will sound the Low drumsample. If you do not wish to use velocity switching, set this to 001 and specify only the High drumsample ("Velocity SW LH" PROG 2. 1­2/3). 5. 1­1b: High (High Sample) Drumsample Bank [ROM, RAM, EXB*. . . ] Specifies the bank of the High drumsample. In "Drumsample, " you can choose from 00: BD-Dry 1 ­ 412: Amp Noise. (VNL) 116 RAM: Selects samples that you created in Sampling mode or loaded in Disk mode. Select the RAM bank when you want to use this sample data to create a drum kit. EXB*: Drumsamples from a separately sold EXB-PCM series option board can be selected. This can be selected only if an option board containing drumsamples is installed. If a drum kit that uses a drumsample from a separately sold EXB-PCM series board is selected, but the necessary drumsample is not available because the corresponding EXB-PCM (expansion board) is not installed, the "Bank" field will indicate ROM. Drum kits 144 (GM)­152 (GM) cannot be edited, but you may copy them to another drum kit and then edit them. 1 Select "Copy Drum Kit" to access the dialog box. 5. 1­2a 5. 1­2b 5. 1­2a: Low (Low Sample) Drumsample Bank 2 Select the copy source drum kit ("From"). 3 To execute the Copy Drum Kit command press the [F8] ("OK") key. To cancel without executing press the [F7] ("Cancel") key. [ROM, RAM, EXB*. . . ] Specifies the bank of the Low drumsample ("Bank" 5. 1­ 1b). Drumsample [0000. . . 3999: Name] Copy Key Setup This command copies the settings of an individual key to another key. You can also copy settings from two or more contiguous keys at once. 1 Select "Copy Key Setup" to access the dialog box. Selects the Low drumsample. This will be sounded by velocities lower than the value set for "Vel. (For details on each drumsample, refer to VNL. ) The drumsample can be selected using the Utility "Select by Category" (5. 1­1d). 2 Specify the beginning of the range of keys to be copied ("From Key"). If you selected multiple keys in "From Key, " they will be copied sequentially, starting at "To Key" and extending upward. 4 To execute the Copy Key Setup operation, press the [F8] ("OK") key. To cancel without executing press the [F7] ("Cancel") key. S. Ofs (Start Offset) Rev (Reverse) Trans (Transpose) Tune Fc (Cutoff) Reso (Resonance) At (Attack) Dc (Decay) "High"(5. 1­1b) s 5. 1­2b: [Off, On] [Off, On] [­64. . . +63] [­99. . . +99] [­64. . . +63] [­64. . . +63] [­64. . . +63] [­64. . . +63] UTILITY Select by Category If ROM is selected for "Bank, " you can select drumsamples by category. For the procedure, refer to "Select by Category" (p. 2) It is not possible to edit the name of a drumsample category or to change the assigned category of a drumsample. "Write Drum Kits, " "Rename Drum Kit, " "Copy Drum Kit, " "Copy Key Setup, " "Select by Category" (5. 1­1d) 118 5. 1­3: Voice (Voice/Mixer) For each key of a drum kit, you can set voice assign, pan, and effect routing etc. nation, or Multi mode 7. 2­1 Setup pages S1 (Send1 (MFX1), " "S2 (Send2 (MFX2)" which are located after the sound passes through IFX1, 2, 3, 4, or 5. Drum kits will sound using the settings of the program that is selected in Program mode. [. . . ] In this owner's manual, "ADAT" is used as a general designation for ADAT compatible multi-track recorders such as the Alesis ADAT. Digitally recording the sound of the TRITON-Rack that has been mixed on a digital mixer to the ADAT 1 Use an ADAT-OPTICAL cable to connect the TRITONRack's DIGITAL OUT connector to the ADAT OPTICAL IN connector of the ADAT Optical format-compatible mixer. 2 Use ADAT-OPTICAL cables to connect the respective IN and OUT connectors of the ADAT Optical format-compatible mixer and the ADAT. 3 Make connections as shown in the following diagram so that an Alesis BRC Remote Controller or other ADAT optical format compatible mixer or remote controller can be used as the master for digital signal synchronization, and connect the WORD CLOCK OUT connector of the mixer to the WORD CLOCK IN connector of the TRITON-Rack. For connections, use a BNC Coax cable made by Alesis Corporation or a BNC cable made for video (both sold separately). [. . . ]