User manual KORG ST 1

[. . . ] E 1 IMPORTANT SAFETY INSTRUCTIONS 1) 2) 3) 4) 5) 6) 7) 8) 9) Read these instructions. No objects filled with liquids, such as vases, shall be placed on the apparatus. Do not block any ventilation openings, install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] This is a very useful technique for creating combinations that use the arpeggiator. Refer to "Arpeggiator settings in Combination and Sequencer modes" (p. 132, PG p. 44), and study the relationship between arpeggiator assignments, "Status, " and "MIDI Channel. " Portamento Normally you will set this to PRG. If you want to overide the portamento setting specified in the program assigned to the timbre to be forced off, set this parameter to Off. Conversely, if you want to force the portamento to be on, or to change the portamento time, set this to a value of 001­127 to specify the portamento time. Pitch page Bank Select (when status=EX2) This setting is valid when "Status" is set to EX2. It specifies the Bank Select message that will be transmitted from TRITON STUDIO. These parameters adjust the pitch of the timbre. · In a layer-type combination, you can set two or more timbres to the same program, and create a richer sound by using "Transpose" to shift their pitch apart by an octave or by using "Detune" to create a slight difference in pitch between the two. · In split-type combinations, you can use "Transpose" to shift the pitch (in semitone units) of the programs specified for each key zone. · If you wish to change the playback pitch of a drum program, use "Detune. " If you change the "Transpose" setting, the relationship between notes and drum sounds will change. 77 Other functions Effects settings Arpeggiator settings Drum kit settings Transpose, Detune (BPM Adjust) System settings SMF playback Creating a CD Sampling settings Producing songs Combination settings Program settings Here you can specify the MIDI status of the internal tone generator assigned to each timbre. Normally when playing the internal tone generator of TRITON STUDIO, you will set this to INT. With settings of EXT or EX2, you can control an external tone generator connected via MIDI. If the timbre is using a program whose "Oscillator Mode" is Double, and you want only OSC1 or OSC2 (not both) to sound, set this to OSC1 (only OSC1 will sound) or OSC2 (only OSC2 will sound). Loading data Saving data Status Basic functions Adjusting the BPM of multisamples or samples created in Sampling mode If a timbre's program uses multisamples or samples that you created in Sampling mode (or loaded in Disk mode) at a specific BPM value, you can use the page menu command "Detune BPM Adjust" to call up a new BPM value. (PG p. 39) For example if you selected a bass program for timbre 1 and a piano program for timbre 2 to create a split-type combination, you could make the following settings so that pressing the connected damper pedal would apply the damper effect only to the piano program of timbre 2. Set the P3: Edit-MIDI Filter-1 "Enable Damper" parameter Timbre 1 "Enable Damper": unchecked Timbre 2 "Enable Damper": checked Other page Layer, split, and velocity switch settings/Controller settings P4: Edit-Zone/Ctrl Key Zone page (Key zone settings) Indicates settings such as layer, split, and keyboard crossfade. By setting key zones, you can create a combination in which different programs sound in different areas of the keyboard. By combining key zones specified for each timbre, you can create layered or split combinations. The upper and lower limits for the key zone of each timbre are set by the "Top Key" and "Bottom Key" respectively. For example in the following diagram, timbres 1­3 are set to create a layered and split combination. Timbre 1 and timbres 2/3 are split between the B3 and C4 note numbers. Timbre 1 Timbre 2 Timbre 3 Brass Strings Piano Delay [ms] Specifies the amount of time before the program assigned to each timbre will sound. Specifies the time from when you play the keyboard until the program will sound. If you select KeyOff for this parameter, the timbre will sound when the note is released. Use Program's Scale, Scale Specifies the scale for each timbre. If you check "Use Program's Scale, " the scale specified by the program will be used. Timbres for which this is not checked will use the Scale setting. MIDI filter settings P3: Edit-MIDI Filter For each MIDI Filter item, you can specify whether or not the corresponding MIDI message will be transmitted and received. [. . . ] However depending on the state in which the disc was saved, it may be converted into ISO9660 level 3 format, and may still not be recognized. In this case if you install ISO9660 level 3 compatible reader software or packet writing software on your computer, it will be possible to recognize the disc. PG p. 299 A CD-R/RW that was saved or copied on the TRITON STUDIO using packet writing is not recognized by the TRITON/TRITON pro/TRITON proX/TRITON-Rack. These models do not support UDF version 1. 5, and therefore will not recognize such a disc. [. . . ]