User manual KORG PE-2000 SCHEMATIC

[. . . ] You'll find the well-designed top panel, TouchView display and dedicated knobs around the display make working with the PE-2000 a breeze!Transport controls shown as follows: [ ] = RECORD [ ] = PLAY [ ] = STOP [ ] = REWIND [ ] = FAST FORWARD First, connect the AC power cable. Make sure that the MONITOR LEVEL knob or HEADPHONE level knob is turned down first, and then connect audio cables from the MONITOR OUT L/R jacks on the rear panel of the unit to your stereo powered monitor system (or connect headphones to the PHONES jack on the front panel). Press the [MAIN] power key on the rear panel press the [ON] key (under the red standby light) on the top panel. Work with one of the demo songs as you tour the mode keys: ! If the demo song "TAKE ME AWAY" is not already loaded in the PE-2000, please restore it from the PE-2000 Factory Data CD that came with the unit. [. . . ] Here you will add volume changes (fader automation) to the drum tracks: 1. Press the [MIXER] key select "FADER/PAN AUTOMATION" in the display then press the "Automation" tab. " radio buttons under channels 1-2 in the Record enable track automation for channels 1 and 2 by pressing the " display so they show " " (record enabled) Press the "Mode" button in the display Select "Overwrite" 3 Select Fader as the type of event to be recorded. Press Automation "OFF" in the upper right of the display to turn it "ON (Rec)" press the [<] [MARK JUMP] to return to to beginning of the song. Press the [ ] key to playback the song and during playback move fader 1 up and down, changing the volume. (channels 1 and 2 are paired, so adjusting channel 1 will also adjust channel 2) When finished press [ ]. Return track automation for channels 1 and 2 to play mode by pressing the " display so they show " " and make sure Automation is set to "ON (Play)" " radio buttons under the channels in the 7. 8. press the [<] [MARK JUMP] and then playback the song to see and hear the events you just recorded. Scene Automation With the scene automation a song can contain 100 "snapshots" of the mixer settings. Fader, Pan, EQ and effects settings are stored with a scene and can be recalled automatically during playback. press the "FADER/PAN AUTOMATION" button in the display then press the "Mixer View" Press the [<] [MARK JUMP] key to return to the beginning of the song. Push faders 1-8 and the MASTER fader all the way up then all the way back down. You can make EQ adjustments by using the dedicated EQ controls to the right of the display. To select EQ presets, press [MIXER] select "EQ/ATT/PHASE" press the "EQ Library" tab. 3. 4. 5. [MIXER] All mixer settings instantly accessible!Here you will find access to input/output assignment, pairing and grouping faders, scene automation, the analog compressors, EQ, effect sends etc. [TEMPO] Tempo, Time signature and Rhythm There are 265 preset metronome / rhythm patterns in the PE-2000. These patterns can be used to create a drum track or Tempo Map with pattern, tempo and time signature changes. The Rhythm Patterns /Tempo Maps that you build do not use actual tracks, but can be recorded to tracks if desired. Press the [TEMPO] Key, and then press the "Prev))" (Preview) button in the display. Press the " " popup button in the lower left of the display (Metro04 L1 is currently selected). Audition some of the patterns by pressing to select them in the display, and by using the <scroll bar> or the DIAL. When finished, press "Cancel", and then press "Prev))" to turn previewing off. In a 24Bit 96kHz song, you will only be able to select Metro, Hi Hat and Blank. [. . . ] 4. Press the [CH SELECT] key for channel 1 Press the [CH VIEW] key. Press the SEND INTERNAL [1] key located in the top right hand corner of the adjustable display. For microphone, select "P25: Male Vocal 1" or "P27: Female Vocal 1" press "Recall" then "Yes". Record with the Metronome / Rhythm Patterns: 1. Press the [TEMPO] key, and then press the "SetUp" tab and select "004: 8bt Rock1", and then press "OK". [. . . ]