User manual KORG NANO KONTROL

[. . . ] You can't specify the button behavior if the assign type is "MMC. " If you've specified "MMC, " an MMC command will be transmitted each time you press the button. Control Change Number [0. . . 127] Specifies the control change number of the control change message that is transmitted. MMC Command [Stop/Play . . . /MMC Reset] Selects one of the following thirteen types of MMC command as the MMC message that will be transmitted. [. . . ] You can specify the message assigned to each button, the way in which the button will operate when pressed, the control change number, the note number, the value transmitted when the button is turned on/off, and the attack time/release time. 4 1c Driver ports The nanoKONTROL's USB-MIDI I/O will be seen from the computer as 1IN-1OUT. As shown in the following table, the name of the ports depend on which operating system you're using, and whether or not you've installed the Korg USB-MIDI driver. OS Mac OS X 10. 3 or 10. 4 Mac OS X 10. 5 or later Windows XP Windows Vista Windows XP/Vista + KORG USB-MIDI Driver MIDI IN nanoKONTROL Port 1 nanoKONTROL SLIDER/KNOB USB audio device nanoKONTROL nanoKONTROL 1 SLIDER/KNOB MIDI OUT nanoKONTROL Port 1 nanoKONTROL CTRL USB audio device nanoKONTROL nanoKONTROL 1 CTRL a. Knob This knob transmits control change messages. Assign Type [No Assign/Control Change/Note] Specifies the message assigned to the slider. Button Behavior [Momentary/Toggle] Selects one of two types of behavior for the button. Momentary Pressing the button will transmit the On value or Note-on message. Toggle Each time you press the button, the On value/Note-on or the Off Value/Note-off message will be transmitted alternately. Control Change Number [0. . . 127] Specifies the control change number of the control change message that is transmitted. Note Number [C-1. . . G9] Specifies the note number of the note message that is transmitted. On Value [0. . . 127] Specifies the value of the message transmitted when the button turns on. If the assign type is set to "Note, " the velocity of the note-on message is specified by the On Value setting. If the On Value is "0, " the velocity will be transmitted as "1. " Off Value [0. . . 127] Specifies the value of the message transmitted when the button turns off. This can be set only if the assign type is "Control Change. " Attack Time [0. . . 127] Specifies the time from when you press the button until the On Value is reached. This can be set only if the assign type is "Control Change. " Release Time [0. . . 127] Specifies the time from when you release the button until the Off Value is reached. This can be set only if the assign type is "Control Change. " CC Value On Value Restoring the factory settings If you turn on the power while holding down the [REC] button, [STOP] button, and [SCENE] button, the settings of the nanoKONTROL will return to their factory-set condition, and the scene LEDs will light up. The process of restoring the factory settings will take several seconds after you turn on the power. [. . . ] (http://www. korg. co. jp/English/Distributors/ or http://www. korg. com) 4. USB connector Connect the nanoKONTROL to your computer with a USB cable via this port. Scene MIDI channel Setup Operating requirements Mac OS X Computer Apple Macintosh computer with an Intel or PowerPC processor that has a USB port and satisfies the requirements for running Mac OS X Operating system Mac OS X 10. 3. 9, or Mac OS X 10. 4. 7 or later Scene MIDI Channel [1. . . 16] Specifies the MIDI transmit channel for each scene. Set this to match the MIDI channel of the MIDI application you're controlling. Group MIDI channel Group MIDI Channel [1. . . 16/Scene MIDI Channel] Specifies the MIDI channel on which each MIDI control group will transmit MIDI messages. [. . . ]