User manual KORG MS-20 SERVICE MANUAL

[. . . ] (Manual: p. ): Refers to a page in the "D32XD/MS-20 Owner's Manual" Warning dialog box added to Format and Partition Change in PC drive size --------------------------- 4 ------------ 4 4 4 5 5 Changes and additions to Edit Track Updating the system For the procedure of how to update the system, refer to the owner 's manual section on "Updating the system" (Manual: p. 95). Optimizing a track (OptimizeTrk) ----------------------------Eliminating noise (NoiseReduction) --------------------------Erasing punch noise (ErasePunchNoise) -------------------Erase a silent region (EraseSilence) -------------------------- New MIXER Navigation Tools Equalizer knobs Added message 1 Added message 2 Added Mixer SetUp -------------------- 6 -------------------------------------- 6 ----------------------------------- 6 ----------------------------------- 6 --------------------------------- 6 CAUTION FOR LASER This product utilizes a laser. Use of control, adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser diode properties Material Semiconductor laser GaAlAs Laser output Less than HHS and IEC 825-1 Class 1 Limit Wave length 784 nm Accessing the Mixer Setup screen ---------------------------- 6 Storing a mixer setup ------------------------------------------- 6 Recalling a mixer setup ----------------------------------------- 7 Top panel keys SCRUB --------------------------------------- 7 -------------------------------------------------- 7 Location of the required label. The following enhancements apply only to the MS-20 ------------------ 8 Changes in PAIR page mode Event Automation --------------------- 8 ----------------------------------- 9 2 Added functionality Control knobs The control knobs can now be used to edit various parameters in the following pages. Sub Mixer1­8; Sub Mixer9­16 (AIB-8 required); Sub Mixer1724 (DIB-8 required); Analog Compresser1­8; Analog Compresser9­16 (ACB-8 required); plus EQ/ATT, Master EQ, Effect 1/2 Send, Aux 1/2/3/4 Send, FaderPan, Cue Level, Ch View The MS-20 does not have an Aux 3/4 Send page. More simultaneous record tracks in the 24-bit mode The number of tracks that can be recorded simultaneously in a 24-bit song at 48 kHz/44. 1 kHz sampling frequencies has increased to 12 tracks (from 8 tracks in previous versions). [. . . ] For D32XD 48 kHz/24-bit or 44. 1 kHz/24-bit songs, only tracks 1-16 can be selected. Erasing punch noise (ErasePunchNoise) Erasing noise from the IN-OUT region of track 1 (1) Specify the region where you want to erase punch noise. ·Set the IN location to a point slightly earlier than where the noise occurs. (2) Select "ErasePunchNoise. " In the TRACK, "EditTrk" tab page, press the Edit Trk Type cell. In the Edit Trk Type dialog box, select "ErasePunchNoise" and press the OK button. (2) (3) For the rest of the procedure, refer to step (5) and following of "Erasing region of silent audio data" (Manual: p. 74). For an overall explanation of ErasePunchNoise, refer to the Reference section Optimize Trk A3. Mode "Erase Silence" (Manual: p. 142). Upgrade Guide 5 New MIXER Navigation Tools Assigning Tab Pages to the Locate keys Tab pages within the MIXER page can be registered to the LOC1/IN­LOC6 keys for quick access. You can move between MIXER page modes by holding down the MIXER key and using the Cursor keys (, ) (Manual: p. 99). Accessing the Mixer Setup screen Press the top panel MIXER key to display the Page Jump Menu screen (Manual: p. 99). Press the MIXER SET UP button to open the Mixer Setup screen. Equalizer knobs When the "Master EQ" tab page is displayed, you can now use the equalizer knobs to edit the GAIN, FREQ, and Q values (Manual: p. 10, 49, 111). The equalizer band keys (High. . . Low) cannot be used in the "Master EQ" tab page. Please refer to Page 3 of this document for more information on the operation of the control knobs when using the Master EQ. Added message 1 In ¯ Out Samples under 4096. To ¯ End Samples under 2048. (Manual: p. 170) The region specified for the track editing operation is too small. Storing a mixer setup Here's how to store the current mixer settings as a mixer setup program. You can't store a mixer setup while a song is playing. Added message 2 (Manual: p. 170) Trigger recording is not available for the master track. You can't perform trigger recording if the MASTER TRACK STATUS key is set to REC. (1) Make the current mixer settings are the ones that you want to store. (2) Access the MIXER, "MIXER SET UP, " "MixerSetUp" tab page. (3) In the list, press to highlight the program in where you want to store the current settings (i. e. , the program you want to overwrite). 6 Top panel keys (4) (3) The MIXER, CD, UNDO and SCRUB keys will now toggle back and forth between the main page jump menu for that key, and the most recently accessed tab page under that key. MIXER key (Manual: p. 10, 99) Pressing the MIXER key displays the page jump menu screen. Group buttons [E, F, G, H] These buttons select the CH ON group for each channel. To assign a channel to a CH ON group, press the corresponding button (it will be highlighted). Group on buttons [E, F, G, H] To enable CH ON grouping, press the corresponding button (highlighted). If these buttons are pressed operating the channel on status of any channel assigned to a group will affect all the channels in that group. When you turn on a 1. "Group button" to add a channel to an existing group, the on/off status of the channel at that moment will determine the on/off status for the group. 3b-2. Fader Group When you operate the fader of any channel that is assigned to a group, the fader levels of the other channels assigned to that group will also change, preserving the balance of the linked channels. Each channel can be assigned to only one of these Fader groups. If you want fader operations to affect the value, set the SYSTEM "Control" tab page Fader/Knob Control setting to "Match. "(Manual: p. 127) 1 2 1. Group buttons [A, B, C, D] These buttons select the fader group for each channel. To assign the channel to a group, press the corresponding button (it will be highlighted). Group on buttons [A, B, C, D] To activate a particular fader group, press the corresponding button (highlighted). If these buttons are pressed, the fader levels will change to preserve the balance of the group when you operate any fader in that group. When you turn on a 1. "Group button" to add a channel to an existing group, the level of the channel at that moment will be set as that fader's balance in the group. 8 Event Automation Both the D32XD and MS-20 support Scene Automation. [. . . ] Event List. " If you press the Event List's Undo button immediately after recording automation, that automation data will be erased, and not the most recent event edit. 3. Select List. " To edit an event, select (highlight) it by pressing it in the list. If D32XD data containing Aux 3 and 4 events is loaded into the MS-20, the Aux 3 and 4 events will always be displayed in the event list. You can select and edit these events in the same way as for other parameters. 4. Free event memory amount This indicates the amount of remaining memory in which you can record events. 4a 4b 3c-3. [. . . ]