User manual KORG KP1 1

[. . . ] In MIDI Edit mode ( "MIDI transmission settings") you can hold down the corresponding switch and rotate the PROGRAM knob to select the desired control number. A control number that has already been assigned cannot be selected in duplicate. Specifications · Number of programs: 60 · Input Control and Connection INPUT SELECT switch MIC: The effect will apply to the MIC input. Peak indicator INPUT VOLUME knob PROGRAM MAP keys (1­6) PROGRAM/LOCATION display MIDI transmission settings When you press the six PROGRAM MAP keys simultaneously, you will enter MIDI Edit mode. If you then perform no operation for approximately 10 seconds or if you touch the touch panel, you will return to normal mode. [. . . ] Handling To avoid breakage, do not apply excessive force to the switches or controls. Do not use liquid cleaners such as benzene or thinner, or cleaning compounds or flammable polishes. Keep this manual After reading this manual, please keep it for later reference. Keeping foreign matter out of your equipment · Never set any container with liquid in it near this equipment. If liquid gets into the equipment, it could cause a breakdown, fire, or electrical shock. If something does slip into the equipment, unplug the AC adaptor from the wall outlet. Then contact your nearest Korg dealer or the store where the equipment was purchased. THE FCC REGULATION WARNING (for U. S. A) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Unauthorized changes or modification to this system can void the user's authority to operate this equipment. CE mark for European Harmonized Standards CE mark which is attached to our company's products of AC mains operated apparatus until December 31, 1996 means it conforms to EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC). And, CE mark which is attached after January 1, 1997 means it conforms to EMC Directive (89/336/EEC), CE mark Directive (93/68/EEC) and Low Voltage Directive (73/23/EEC). Also, CE mark which is attached to our company's products of Battery operated apparatus means it conforms to EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC). You can control the sound by using your finger to rub or tap (strike lightly) this panel. Affix the included protective label. PHONES jack, PHONES VOLUME knob MIDI OUT connector Cable hook PHONO input jacks 8 DIST+FILTER 10 DISTORTION 11 PHASER 12 PHASER 13 LFO WAH 14 STEP PHASER 15 DIST+PHASER 16 MANUAL FLANGER 17 MANUAL FLANGER 18 PITCH SHIFT 19 TREMOLO 20 STEP PHASER 21 TAPE ECHO 22 DELAY 23 DELAY 24 STEREO TAPE ECHO 25 MEDIUM DELAY 26 LONG DELAY 27 X DELAY FX BALANCE, DIST GAIN Rub fast with beat A record turntable can be connected to these jacks. GND (ground) terminal 9 ISOLATOR TYPE FILTER FREQ FREQ (MANUAL) DI/FX BALANCE, RESONANCE Rub slowly Loop the cable around this hook to prevent accidental disconnection. DC IN jack POWER switch LINE OUT jacks Connect this to the ground terminal of your record turntable. TRIM Connect the included AC adaptor (DC12 V 700 mA ) to this jack. CONNECTION switch Adjust this as appropriate for the sensitivity of your mic, so that distortion does not occur. Connect these jacks to your mixer or audio system. MIC input jack A mic can be connected to this jack. LINE IN (input) jacks Normally you will set this in the DIRECT position. [. . . ] The previously-recorded phrase will be erased, and a new phrase will be recorded. If you turn off the power switch or change programs, the recorded phrase will be erased. 28 TALK FILTER+DELAY FILTER FREQ 29 DIST+FILTER+DELAY FREQ 30 DELAY+FILTER FOR DUB TIME 31 REVERB (HALL) 33 REVERB (PLATE) 35 DELAY+REVERB 36 DELAY+REVERB LOW CUT LOW CUT DELAY LEVEL DELAY TIME 32 GATE REVERB (HALL) LOW CUT 34 GATE REVERB (ROOM) LOW CUT 37 TALK FILTER+REVERB FILTER FREQ 38 DIST+FILTER+REVERB FILTER FREQ 39 REVERB+PAN 40 REVERB 41 STEP MODULATION 42 RING MOD+FILTER 43 RING+TALK MOD 44 SPECIAL ECHO 45 RING+DELAY 46 DELAY+TREMOLO 47 3D PAN 48 VIBRATE 49 STEP FLANGER 50 STEP PHASER 51 SAMPLE/PLAY1 52 SAMPLE/PLAY2 53 SAMPLE/PLAY3 PAN REVERB TIME MOD DEPTH RING FREQ MOD SPEED TIME TIME PAN (L/R) SPEED+DEPTH LFO SPEED LOOP TIME TIME STRETCH REV LEVEL+RESONANCE Tap with snare drum Handling the touch panel Never press down too hard on the touch panel, or place a heavy object on it. Rubbing or pressing the touch panel with a sharp object can scratch it, so only use your finger to operate it. Using solvents such as thinner may melt the surface of the touch panel. TIME+LFO SPEED DLY+TREM X-FADE About the PROGRAM/LOCATION display When selecting a program: the program number (1­60) will be displayed. [. . . ]