User manual KORG KAPTIVATOR 1

[. . . ] OWNER'S MANUAL Precautions Location Using the unit in the following locations can result in a malfunction. · In direct sunlight · Locations of extreme temperature or humidity · Excessively dusty or dirty locations · Locations of excessive vibration · Close to magnetic fields Power supply Please connect the designated AC adapter to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended. Interference with other electrical devices Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions. Handling To avoid breakage, do not apply excessive force to the switches or controls. Care If the exterior becomes dirty, wipe it with a clean, dry cloth. [. . . ] parameter, use the VALUE knob to change the value shown in the VALUE display. NOTE The decimal point following the parameter value will light if the value is identical to the saved value. 4 To edit the next parameter, press the EDIT key. Each time you press the EDIT key you will proceed to the next parameter. To return to the preceding parameter, hold down the EDIT key and press the YES/WRITE key. At this point, you can use the VALUE knob to select the desired save-destination style and press the YES/WRITE key to save the edited style and complete the procedure. If you want to continue editing without saving your changes, press the NO/ESC key. Owner's Manual 19 Customizing a Style --Style Editing Editing examples Changing the operation of the ribbon controller 1 Select the style that you want to edit. The display will indicate "A1. **" and the EDIT key will blink. To choose the ribbon controller, choose a setting in the range of "G1"­"G4. " With the "G1" setting, the effect will intensify as you move the controller from bottom to top. Conversely with the "G2" setting, the effect will intensify as you move from top to bottom. With the "G3" setting, the effect is at maximum at either end, and minimum in the center. The "G4" setting produces the opposite result, with the maximum effect in the center position. Use the VALUE knob to select the destination style location (style number) where you want to save the edited style. If you decide not to save the changes you made, press the NO/ESC key. Changing the wipe type 1 Select the style that you want to edit. The display will indicate "A1. **" and the EDIT key will blink. In this example, let's select "03" to produce a wipe that changes the position of the images. Choose "F2" if you want to invert the direction of the fader operation. This parameter specifies the type of wipe and the variable range of the controller. If you want to create a wipe that pushes the image from left to right, specify a value in the range of "30"­ "39. " The second digit of the value specifies the range of fader movement. In this case, selecting "30" will produce a wipe using the entire range of the fader. Selecting "39" will cause the image to switch at the midpoint of the fader. Use the VALUE knob to select the destination style location (style number) where you want to save the edited style. If you decide not to save the changes you made, press the NO/ESC key. 20 1. Sampling Sampling video Sampling a video input source 1 Press the SAMPLE key; it will blink, and you will be in Sampling mode. [. . . ] The DATA PROCESS(LOAD) ERROR(Function:24h) message will be transmitted in other cases. 1-5 SYSTEM EXCLUSIVE MESSAGES FUNCTION CODE LIST (TRANSMIT) +-------------------+------------------------------+---+---+ | Function ID [Hex] | Description |R|E| +-------------------+------------------------------+---+---+ | 51 | Global Data Dump |o| | | 65 | All Style Data Dump |o| | | 79 | 1 Motion Sequence Data Dump | o | | | 7B | 10 Motion Sequence Data Dump | o | | | 23 | Data Process(Load) Completed | | o | | 24 | Data Process(Load) Error | |o| +-------------------+------------------------------+---+---+ Transmitted when R : Request message is received and data dump from MIDI dump page. E : Exclusive message received. MIDI Implementation 97 (3) 1 MOTION SEQUENCE DATA DUMP REQUEST R +----------------+------------------------------------------------+ | Byte [Hex] | Description | +----------------+------------------------------------------------+ | F0, 42, 3n, 77 | Exclusive Header KTV1 | | 0111 1000 (78) | 1 Motion Sequence Data Dump Request 78h | | 0mmm mmmm (mm) | Dump Motion Number (mm = 00h~63h) | | 1111 0111 (F7) | EOX | +----------------+------------------------------------------------+ When this message is received at the MIDI dump page, the 1 MOTION SEQUENCE DATA DUMP(Function:79h) message will be transmitted. The DATA PROCESS(LOAD) ERROR(Function:24h) message will be transmitted in other cases. (4) 10 MOTION SEQUENCE DATA DUMP REQUEST R +----------------+------------------------------------------------+ | Byte [Hex] | Description | +----------------+------------------------------------------------+ | F0, 42, 3n, 77 | Exclusive Header KTV1 | | 0111 1010 (7A) | 10 Motion Sequence Data Dump Request 7Ah | | 0000 pppp (0p) | Dump Motion Page Number (0p = 00h~09h) | | 1111 0111 (F7) | EOX | +----------------+------------------------------------------------+ When this message is received at the MIDI dump page, the 10 MOTION SEQUENCE DATA DUMP(Function:7Bh) message will be transmitted. [. . . ]