User manual KORG EXB-RADIAS FOR M3

[. . . ] E 1 About this manual About the EXB-RADIAS for M3 operating manual This EXB-RADIAS for M3 operating manual explains the RADIAS program functions and parameters that are available when the EXB-RADIAS synthesizer board is installed in the M3 music workstation/sampler. For details about basic operation of the M3 and on the functions and parameters not related to the EXB-RADIAS, refer to the M3 operation guide and parameter guide. Conventions in the operating manual Abbreviations in the operating manualOG, PG When indicating reference pages, the various operating manuals of the M3 may be abbreviated in the following ways. M3 OG: M3 Operating Guide M3 PG: M3 Parameter Guide Parameters in the LCD display screen " " Parameters displayed in the display are enclosed in double quotation marks " ". Symbols , , Note, Tips These symbols respectively indicate a caution, a MIDIrelated explanation, a supplementary note, or a tip. Example screen displays The values of the parameters shown in the example screens of this manual are only for explanatory purposes, and may not necessary match the values that appear in the display of your instrument. MIDI-related explanations CC# is an abbreviation for Control Change Number. In explanations of MIDI messages, numbers in square brackets [ ] always indicate hexadecimal numbers. * Company names, product names, and names of formats etc. [. . . ] Waveform Modulation (000. . . 127): Controls the oscillator 1 waveform when OSC1 Mod is Waveform. Cross Modulation Depth (000. . . 127): Controls the depth of cross modulation for oscillator 1 when OSC1 Mod is Cross. Unison Detune (000. . . 127): Controls the pitch difference between unison oscillators when OSC1 Mod is Unison. Formant Width (000. . . 127): Controls the frequency components of the formant. Resonance (000. . . 127): Controls the amount of resonance for the noise generator. OSC1 Control2 (000. . . 127/­63. . . +63/01. . . 32/ LPF63. . . CNT. . . HPF63/01. . . 64l/L63. . . CNT. . . R63, Absolute): Controls a parameter appropriate for the modulation type of oscillator 1. (000. . . 127): Controls the amount of change in the oscillator 1 waveform. Unison Phase (000. . . 127): Controls the relative phase of the oscillators at note-on. Formant Offset (­63. . . +63): Shifts the frequency spectrum of all formants. LPF/HPF Mix (LPF. . . CNT. . . HPF): Controls the mix balance between the low pass filter and high pass filter inside the noise generator. Balance (L001. . . C064. . . R127): Controls the left/right channel balance of the input signal. OSC2 Waveform (Saw. . . Sine, Absolute): Selects the oscillator 2 waveform. OSC2 Mod (Off/Ring. . . RingSync, Absolute): Selects the modulation type for the oscillator. OSC2 Semitone (­24. . . +24, Absolute): Controls the amount of detune (semitone units) relative to oscillator 1. OSC2 Tune (­63. . . +63, Absolute): Controls the amount of detune relative to oscillator 1. OSC1 Level (000. . . 127, Absolute): Controls the output level of oscillator 1. OSC2 Level (000. . . 127, Absolute): Controls the output level of oscillator 2. Noise Level (000. . . 127, Absolute): Controls the output level of the noise generator. FilterA Type/Balance (LPF24. . . LPF12. . . HPF. . . BPF. . . THRU, Absolute): Selects the filter type for filter A. FilterA Cutoff (000. . . 127, Absolute): Controls the cutoff frequency of filter A. FilterA Resonance (000. . . 127, Absolute): Controls the resonance of filter A. FilterA EG1 Intensity (­63. . . +63, Absolute): Controls the depth by which EG1 will modulate the cutoff frequency of filter A. FilterA Velocity Sens (­63. . . +63, Absolute): Controls the depth by which velocity will modulate the cutoff frequency of filter A. [. . . ] If you specify Bank as the range to be loaded, select I-F as the load-source data, and I-F or a user bank set to the RADIAS bank type as the load-destination ("To:"). Press the OK button to execute, or press the Cancel button to cancel. If you specify Single as the range to be loaded, select a program from bank I-F as the load-source, and a program number in I-F or a user bank set to the RADIAS bank type as the load-destination ("To"). 65 Set Program User-Bank Type This specifies the bank type for Program mode program banks USER-A through G. If you've set the bank type to RADIAS, the RADIAS programs you create can be saved in the corresponding user bank. Before you execute, uncheck Program in Memory Protect (M3 parameter guide p. 359). [. . . ]