User manual KORG CA-40

[. . . ] Objects referred to in this guide: D12 top panel objects that you'll work with are: Keys, Dial, Faders and Pan/Balance knobs. D12 Display objects that you'll work with are: Tabs, Popup and Radio buttons, Dialog boxes and Icons. Navigating the D12: To select the tabs in each mode, repeatedly press a mode key: [INPUT/TUNER], [EQ/PHASE] etc. To move to different locations in the display, press the [CURSOR] key (u). [. . . ] u to the "New" button in the lower right of the display and press ENTER. On the "MakeNewSong" page, u to the "OK" button and press ENTER. The next - available empty song location ("NEW SONG") will be selected. You can set "16 Bit / 16 Track" or "24 Bit / 8 Track" SongType in the "MakeNewSong" page. For this exercise, leave the song type set to "16 Bit / 16 Track": Note: 3. Press [TEMPO/RHYTHM], then u to the "Rhythm:Off" button and press ENTER to set "Rhythm:On", and you'll hear a standard metronome "click": 24 KORG D12 Guided Tour Audition some PCM rhythm patterns: 4. u to highlight "Metro4": 5. 6. Slowly rotate the [DIAL] to the right, to select and listen to some of the patterns in memory. u to the "Vol" parameter and use the [DIAL] to set the rhythm level. After you're finished auditioning patterns, u to the "Rhythm:On" button and press ENTER to turn "Rhythm:Off" and stop pattern playback. The rhythm patterns indicated by "I", "F", or "E" indicate intro, fill, or ending type patterns. More information on recording patterns to tracks later in this guide. Note: Recording and Editing Basics Note: The CURSOR key is indicated by Create a new song: 1. u to the "New" button and press ENTER, then u to the "OK" button and press ENTER. When you're finished, press [STOP], then press [IN/LOC1] (lit) to reset the song to the beginning (check the Counter: "001. 01. 000"). 16. (The internal microphone is automatically muted on playback) Select, assign and record another track: 1. Press the Track 1 [TRACK STATUS] key 2x, until its LED lights GREEN (play status). Press the Track 2 [TRACK STATUS] key 2x, until its LED lights RED (record status). u to the "Ch2" icon, then rotate the [DIAL] to the left, until the "Ch2" input icon reads "1". Note: You've just eliminated the need to re-patch your mic to another analog input!When using external sources, this is the procedure for assigning channels to inputs. Note however, that the internal mic INPUT switch can be set to channel 1 or 2 on the front panel. Speak into the internal mic and raise the Channel 2 Fader to the "0" position. You've already set the input gain for analog input 1, so there's no need to worry about adjusting trim on the new track. Watch the counter in the upper right of this page, and record for about the same amount of time as the first track (adjust playback with the TRACK 1 Fader to suit). [. . . ] 36 Storing Scenes: SONG key Ô Select and move to Counter location desired Ô Adjust Fader, Pan, EQ and Effects as desired Ô STORE key Ô SCENE key. 39 Automatically switching Scenes during song playback: SONG key Ô SCENE key on (red) Ô Select and move to Counter location desired Ô Press PLAY key ÔOM pg. 39 Using the Scrub function to find a time location: SCRUB key Ô Select > to select track Ô Select OK Ô Rotate DIAL to desired location ÔOM pg. 36, 101 Using the Scrub function to playback tracks at half-speed: SCRUB key Ô Select > to select track Ô Select OK Ô Press FF to playback Ô STOP ÔOM pg. [. . . ]