User manual KORG AX3000G

[. . . ] AP2: Choose this setting if you're connected to an amp with a distinctive sounding Mid-range such as a UKmanufactured open-back combo Amp. AP3: Choose this setting if you're connected to a stack with a closed-back 4 x12 cabinet(s). Tuning When you power-on the AX3000G and make the connection settings above, you'll be in "Program Select" mode. You can then choose to tune your guitar in one of two ways: To tune audibly: 1. [. . . ] The PROGRAM SELECT 3 switch LED will light and the Bank Display will indicate 2, and stay lit. ! If the LED in the upper left of the Bank Up switch is lit green, Individual Mode is selected. Press the BANK UP switch to choose Program Select mode. Saving a Program You've tweaked and turned some knobs, and you like the changes that you've made ­ now to save your program: 1. The name display indicates "*WRITE*", and the BANK display and PROGRAM LED's 1­4 will flash. Use VALUE KNOB 1, the / buttons, or the BANK UP/DOWN switches to select the bank you want to use; then use the </> buttons, or PROGRAM SELECT switches to select the destination program 1­4. The program will be saved, the name display will indicate "COMPLETE, " and you'll return to Program Select mode. ! The newly-saved program writes over the previous contents of that bank/program. If you decide not to store your new program, press the EXIT button to cancel the procedure. Note that if you switch to a different program or turn off the power without storing the Program you edited, your changes will be lost. Individual Mode In this mode, you can individually turn each effect type on or off just as if you were using a collection of stomp boxes. To enter INDIVIDUAL mode from PROGRAM SELECT mode, press and hold the BANK UP switch for about one second; the LED above the BANK UP switch will light green. Here's how to switch the pre-effect and reverb on or off while you're playing: 2. Press the "program select" switch 1 to turn the pre-effect on/off. The LED 1 lit/ dark state indicates the on/off status of the pre-effect. The LED at the upper left of the BANK DOWN switch will be lit or dark to indicate the reverb's on/off state. To exit INDIVIDUAL mode, press the BANK UP switch, and the green LED will go dark (not lit). Expression Target Quick Assign Here you can easily assign many effect parameters of the AX3000G to its expression pedal for real time live control!For example, you can assign the speed of a modulation effect, time of a delay, or mix of the reverb to the expression pedal. [. . . ] Control the speed of the ESS with the expression pedal EX2: Major Arpeggio ESS Based off of the preset program 6-4 which was originally a minor arpeggio using a 7A Pattern. 4 AX3000G EasyStart Step 2 has been changed from -9 to -8, and step 5 from 3 to 4 (this changes it to a major arpeggio) The ESS settings are as follows: SMOOTH 0 Pitch shifter: Delay: Time: 756, Reverb: STEPMODE 7-A STEP1 -12 STEP 2 -8 STEP 3 -5 STEP 4 0 STEP 5 4 STEP 6 7 STEP 7 12 Pitch=0, Fine=0, tracking=80, direct=0. 0, effect=7. 0 2 Tap Delay Tone 7. 9, Tap Time 5. 0, Mix 4. 4 Feedback 4. 4, Slap. . . Time=7. 7, Lo Damp 3. 7, High Damp 5. 4, Pre Delay 0, Mix 4. 5 The Control Switch You can assign the control switch to function in a variety of ways. It can act as an on/off for your effects/amp/cab models; a tap tempo for modulation or delay, or even as a trigger for the ESS. [. . . ]