User manual KORG AX10B

[. . . ] · In direct sunlight · Locations of extreme temperature or humidity · Excessively dusty or dirty locations · Locations of excessive vibration Power supply Please connect the designated AC adaptor to an AC outlet of the correct voltage. Do not connect it to an AC outlet of voltage other than that for which your unit is intended. Interference with other electrical devices This product contains a microcomputer. Radios and televisions placed nearby may experience reception interference. Operate this unit at a suitable distance from radios and televisions. Handling To avoid breakage, do not apply excessive force to the switches or controls. Care If the exterior becomes dirty, wipe it with a clean, dry cloth. [. . . ] The DRIVE-AMP effect block is now bypassed, and the name display will indicate "OFF-. " For some effects, it is not possible to simultaneously use the MODULATION and PEDAL effect blocks, or the PEDAL and AMBIENCE effect blocks. If you attempt to turn on both effect blocks in such a combination, the block that had been turned on will automatically be turned off. Editing effects Rotate the effect select knob of the effect block that you wish to edit, or press the corresponding effect block select switch. The effect block LED will begin blinking, indicating that it has been selected for editing. Use the effect select knob, effect block select switch, and value knobs to edit the settings. If you wish to save the edited effect, perform the "Program write" operation. If you fail to do this, the effect program will revert to its original settings when you turn off the power or select a different program. As an example, we will explain how to edit the TUBE OD (Tube Overdrive) effect of the DRIVE-AMP block. If the name display indicated "TUBE OD" when you pressed the effect block select switch, simply continue. If not, turn the DRIVE-AMP effect select knob to the TUBE OD position. If the effect select knob was already located at TUBE OD, first select a different effect model, and then turn the knob back to TUBE OD. The effect block LED will begin blinking, indicating that it has been selected for editing. (The name display will indicate the model name as "TUBE OD. ") If you selected a programmed effect, the ORIG icon will light. The five value LED's will light, and the corresponding value knobs will be assigned to DRIVE, LEVEL, TREBLE, MIDDLE, and BASS respectively, and will function as knobs that adjust the value of each parameter. Turn on the power while simultaneously holding down the EXIT switch and the bank switch. The name display will indicate "RELOAD?" If you press the EXIT switch, the reload operation will not occur; the power-on display will appear, and you will enter Play mode. 2. The name display will change to "RELOAD, " and the reload operation will begin. When the reload operation is completed, the display will indicate "COMPLT" for approximately one second. Then the power-on display will appear, and you will enter Play mode. Never turn off the power during the reload operation. When you perform the reload operation, all user programs will be rewritten. Master level, metronome, and input level settings will also be initialized. 1. Turn on the power while simultaneously holding down the EXIT switch and the PEDAL effect block select switch. The name display will show "PEDAL" for approximately one second, and will then indicate "MIN. " 2. When it stops, release your hand and press the WRITE key. The name display will change from "MIN" to "MAX. " If you decide to halt the adjustment procedure, press the EXIT switch. Press slowly The LCD display will indicate "COMPLT" for approximately one second. After the adjustment procedure has been completed, verify the operation of the pedal. [. . . ] Since you can use the pedal to control the input level to the delay, you can easily produce special effects such as sound-on-sound. TAP DELAY "TAP DLY" This is a tap tempo delay that allows you to set the delay tempo by pressing the pedal switch twice. Knob 3 TONE Knob 4 ------ Knob 5 MIX Adjust the tone of the effect sound. -------- Adjust the mix amount of the effect sound. Knob 2 REVERSE OFF: When you press the pedal, the sound will playback to the end and then stop. [. . . ]