User manual KONICA PROOFREADY GETTING STARTED GUIDE REV 4

[. . . ] ProofReady for Konica RIP Getting Started Guide ProofReady for Konica RIP Getting Started Guide AG50335P3 Rev. 4 ii ProofReady for Konica RIP Getting Started Guide AG50335P3 Rev. 4 ProofReady for Konica RIP Getting Started Guide This guide reflects the Proofready for Konica RIP Getting Started Guide as of February 2003. © copyright Konica Corporation 2003 Proprietary Notice The information contained within this guide is the property of Konica Corporation. [. . . ] Otherwise, click the Quit button to close the Install window. CONFIGURING THE RIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Now that you have installed the ProofReady Plug-in, the next step is to configure the RIP so that it recognizes your proofer. Select Start > Programs > ECRM RIP 6. 0> ECRM RIP 6. 0 Click on ECRM RIP in the top menu, and click on Configure RIP from the drop down menu. Step 1 Step 2 AG50335P3 Rev. 4 ProofReady for Konica RIP Getting Started . . . . . 13 PROOFREADY PLUG-IN ·The Configure RIP window displays. Step 3 Click on the Extras button. ·The Configure RIP Extras window displays. Step 4 Use the scroll bar to choose the proofer to add (e. g. , HP DesignJet 3000 Series) and click on the ADD button. ·The Enable Feature window displays. Step 5 Step 6 Enter the password provided. (Typically, this is a 7-digit number) Click OK. 14 ProofReady for Konica RIP Getting Started AG50335P3 Rev. 4 PROOFREADY PLUG-IN ·The Configure RIP Extras window displays, with Yes applied to the plugin. Step 7 Step 8 Step 9 Click OK. 4 ProofReady for Konica RIP Getting Started . . . . . 15 PROOFREADY PLUG-IN PROOFREADY PAGE SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Now that you have installed the plug-in for your proofer, the next step is to create a page setup for the proofer. For detailed information read the Epson ProofReady. pdf or the HP ProofReady. pdf in the Documentation folder of the ECRM RIP CD. Launch the RIP. Step 1 ·The RIP windows display. Step 2 Click on ECRM RIP from the main menu and select Page Setup Manager. ·The Page Setup Manager window displays. Step 3 Click on the New button. 16 ProofReady for Konica RIP Getting Started AG50335P3 Rev. 4 PROOFREADY PLUG-IN ·The New Page Setup dialog box displays. For instructional purposes the New Page Setup dialog box is divided into eight sections. The instructions in this part of the document is divided into eight corresponding sections. Each is labeled with its corresponding number in the New Page Setup dialog box. AG50335P3 Rev. 4 ProofReady for Konica RIP Getting Started . . . . . 17 PROOFREADY PLUG-IN Selecting and Configuring the Device 1 Step 1 Click on the Device down arrow, and choose the proofer from the list provided. Step 2 Click on the Configure device button in the new page setup dialog box. 18 ProofReady for Konica RIP Getting Started AG50335P3 Rev. 4 PROOFREADY PLUG-IN ·The Configure Device dialog box displays. Step 3 Choose the output method you are using by clicking on the down arrow in the output method box. If you choose Network, the file output remains the default values, fill in the IP address with the IP address of your device, and set the Port Number to 9100 for Jet Direct single printer or 515 for 10/100 Base-T type B Ethernet card. 4 ProofReady for Konica RIP Getting Started . . . . . 23 PROOFREADY PLUG-IN ·The page layout dialog box displays. Step 2 Step 3 Step 4 Check the Center page on media width checkbox. Click on the down arrow in the Page size information field and select the appropriate page size or other. ·If other is selected enter page width. (You can enter any number for a roll selection). Step 5 Click OK. Resolution 5 Step 1 Click on the down arrow in the Vertical information field, and select the value that is appropriate for selected proofing device. (This should match your calibration selection for resolution. ) Click on the down arrow in the Horizontal information field, and select the value that is appropriate for selected proofing device. Check Override resolution in job checkbox. Step 2 Step 3 24 ProofReady for Konica RIP Getting Started AG50335P3 Rev. 4 PROOFREADY PLUG-IN Processing 6 Step 1 Step 2 Click on the down arrow in the Optimization information field, and select None. Do not check Enable Feature. Effects 7 Step 1 Step 2 Step 3 Step 4 Do not check Negative. (disabled) Select rotation value as needed. Scaling 8 Step 1 Step 2 Vertical should be set to 100%. Horizontal should be set to 100%. Saving the Page Setup Step 1 Click on the Save As button in the New Page Setup dialog box. AG50335P3 Rev. 4 ProofReady for Konica RIP Getting Started . . . . . 25 PROOFREADY PLUG-IN ·The save page set up dialog box displays. Step 2 Type a name in the information field, and click on the Save button. ·The Page Setup Manager window displays with the new page setup listed. [. . . ] 4 ProofReady for Konica RIP Getting Started . . . . . 37 PROOFREADY PLUG-IN Step 6 Click on the down arrow in the CMYK Input Profile, and select the item you wish to match. Step 7 Step 8 Click on the down arrow in the RGB Output Profile information field, and select none. Click on the ICC Output information field, and select the proofing paper and resolution you used in the Page Setup/Calibration and Dot Gain/Calibration section. Step 9 Click on ICC Rendering Intents information field and click on ICC Perceptual (if available). 38 ProofReady for Konica RIP Getting Started AG50335P3 Rev. 4 PROOFREADY PLUG-IN Step 10 If your input job was on a creamy yellowish paper, but the proof is on a bright white paper check the Fill background with paper color of input job. Click on the Save as button. Step 11 Step 12 Step 13 Step 14 ·The Save Setup window displays. Step 15 Type in a name and click the Save button. [. . . ]