User manual KONICA PAGEPRO 1350EN

[. . . ] PageProTM 1350EN User's Guide 4136-9562-00A 1800813-001A Trademarks KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC. PagePro is a trademark or registered trademark of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. All other trademarks and registered trademarks are the property of their respective owners. Copyright Notice Copyright © 2006 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. , Marunouchi Center Building, 1-6-1 Marunouchi, Chiyoda-ku, Tokyo, 100-0005, Japan. This document may not be copied, in whole or part, nor transferred to any other media or language, without written permission of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Notice KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. [. . . ] If you can custom-size your page in your application, use those sizes given for the imageable area for optimum results. About Media 33 Loading Media How do I refill Tray 1? Refill the tray only when it is completely empty. Squeeze the right paper guide and open the paper guides. 1 2 Load the media lengthwise and printing-side up in the tray. If media is loaded past the media limit mark, it may not be fed correctly. Load letterhead with the side to be printed facing up and the preprinted letterhead at the top (facing the printer). Squeeze the right paper guide and adjust the paper guides so that both the left and right sides of the media are secure. Then, re-place the tray cover onto Tray 1. 3 34 Loading Media How do I refill the manual feed tray? 1 2 When using the manual feed tray, the sheet of paper must be fed in one at a time. Open the paper guides. 3 Insert the sheet of paper as far as possible into the manual feed tray with the side to be printed on facing up, and then adjust the paper guides so that both sides of paper are aecure. Loading Media 35 Printing on Media How do I load and print custom media? Do not use custom media that does not have approved dimensions Width: 76 mm (3") up to 216 mm (8. 5") Length: 127 mm (5") up to 356 mm (14") 1 2 3 4 In the printer driver (Setup tab/Media Type option), select Plain Paper. Set the media size (Paper tab/Original Document Size/Edit Custom. . . ) Load the custom media lengthwise and printing-side up in Tray 1. Adjust the paper guides to the width of the custom media. Note Improperly adjusted guides may cause poor print quality, media jams, or printer damage. 5 Print the custom media. How do I load and print envelopes? Before printing on envelopes, we recommend printing a test page. If the print result is not oriented as desired, select Rotated (Paper tab/ Orientation option). Do not use envelopes that have Sticky flaps Tape seals, metal objects, paper clips, fasteners, or peel-off strips for sealing Transparent windows Rough surface Material that will melt, vaporize, or emit dangerous fumes Been presealed 36 Printing on Media Use envelopes that are Common office envelopes with diagonal joints, sharp folds and edges, and ordinary gummed flaps Approved for laser printing Dry 1 2 3 4 5 6 In the printer driver (Setup tab/Media Type option), select Envelope. Select the size of the envelope (Paper tab/Original Document Size option). Place the envelopes on a flat surface, and flatten them by pressing down the corners. Flex the envelope stack (including the edges) to remove any stiffness. Correct any bent corners, and tap the envelopes on a flat surface to align them. Squeeze the right paper guide and open the paper guides. 7 Load the envelopes lengthwise and the printing-side up as shown in the illustrations. Printing on Media 37 Note Print envelopes on the front address side only. Some parts of the envelope consist of three layers of paper--the front, back, and flap. Anything printed in these layered regions may be lost or faded. 8 Recheck the paper guides to make sure they are adjusted to the width of the envelopes. Note Improperly adjusted guides may cause poor print quality, media jams, or printer damage. 9 10 Print the envelopes. Open the flap of each envelope immediately (before it cools) after the envelope is delivered to the output tray. Because the envelopes pass through heated rollers, the gummed area on the flaps may seal. Using envelopes with emulsion-based glue avoids this problem. How do I load and print labels? A label consists of a face sheet (the printing surface), adhesive, and a carrier sheet: The face sheet must follow the plain paper specification. The face sheet surface must cover the entire carrier sheet, and no adhesive should come through on the surface. [. . . ] You should now be able to select `USB001'. 72 Note for Windows Me/98SE USB users Installing Accessories Introduction Note Use of accessories not manufactured or supported by KONICA MINOLTA will void your warranty. Dual In-Line Memory Modules (DIMMs) 128 MB DIMM (unbuffered) Note Installing accessories always requires that the printer and accessories are turned off and unplugged during installation. Antistatic Protection Note If an antistatic wrist strap is provided in your printer option kit, attach one end of it to your wrist and the other end to any convenient electrical ground (for example, the bare metal chassis of equipment, as on the back of a computer, that is plugged in but turned off). Never attach the wrist strap to any piece of equipment with an electrical current present. Plastic, rubber, wood, painted metal surfaces, and telephones are not acceptable grounding points. [. . . ]