User manual KONICA CR-241

[. . . ] · Every effort has been made in the preparation of this manual to ensure the accuracy of its contents. However, should you have any questions or find any errors, please contact a Minolta-authorized service facility. · MINOLTA will not accept any responsibility for consequences arising from the use of the instrument. · Company names and product names which appear in this manual are their trademarks or registered trademarks. [. . . ] To save image data, insert the optional compact flash card VI-A12 into the PC card adapter VI-A13, then insert the adapter into the slot. · Make sure that the compact flash card and PC card adapter are positioned in the correct direction when they are inserted. · This memory card is designed for use with the VIVID 900/910 only, so it must not be used with any other VIVID models. Data saved by the VIVID 900 can also be retrieved by this instrument. Note Ref. For a description of data file management (saving, loading, selecting etc. ), refer to pages 45 to 50. [Inserting/Ejecting the PC Card Adapter] 1 When inserting the compact flash card into the PC card adapter, make sure that it is correctly oriented. The PC card adapter VI-A13 with the compact flash card VI-A12 inserted is called the memory card in this manual. Note [Inserting] 1 Position the memory card so that the " " mark on the memory card is aligned with " " on the VIVID 910, then insert the memory card into the slot. · Make sure that the memory card is inserted into the slot until the eject button pops out. · The memory card will be accessed immediately after it has been inserted, so do not remove it for at least five seconds. Note [Ejecting] 1 Press the eject button. · Never attempt to eject the memory card while scan is performed after is pressed. · Never attempt to eject the memory card during data loading or saving. Doing so may damage the VIVID 910 or memory card. Note 21 Notes When Using the Instrument with Tripod When using the instrument with the tripod, first attach the tripod base plate to the instrument, and then attach the instrument to the panhead/tripod. To improve scanning accuracy, it is recommended that scanning be performed via the personal computer connected to the instrument, instead of pressing the [RELEASE] key. CAUTION · Make sure that the tripod base plate, panhead and tripod are secured to the instrument and each fastener on the tripod is firmly tightened. Failure to observe this point may result in the tripod overturning or the instrument dropping. · When placing the tripod on a floor, examine the floor conditions and flatness to make sure that the tripod is stably placed. · After measurement is completed, the instrument must be removed from the tripod before storing them. · Dust and dirt collected on the lens mount surface on the body side must also be removed with a camera air blower etc. Note Ref. For display of the status information, refer to page 51. [Replacing Procedure] 1 Remove the lens hood. Memo The lens hood can be fixed with its bayonet mount. 2 Turn the lens fixing ring counter-clockwise to loose it completely. Memo The lens fixing ring can be fixed with its screw mount. 27 Replacing the Lens 3 Hold the external edge of the fixing ring and pull it out. Memo Hold the ring with your finger located near the red mark on the lens. Attach the lens cap to the removed lens, place it in the lens case and keep it in a safe place. Note The following information will appear in the viewfinder as shown on the right. Check the serial number of each lens displayed. CHANGE LENS TELE S/N MIDDLE S/N WIDE S/N PRESS ANY KEY 2001005 2001005 2001005 4 Attach the desired lens. · Align the red mark on the lens with the one on the lens mount socket, and insert the lens until a click is heard. Memo · The position of the red mark on the lens varies with the focus point. · Hold the ring with your finger located near the red mark on the lens. This will facilitate inserting the lens. 5 Turn the lens fixing ring clockwise to secure the lens. 28 Replacing the Lens 6 Attach the lens hood. Make sure that the notch is aligned with that on the lens, and turn the hood. Memo The hood must be turned until it contacts the bayonet mount socket. 7 Press any key. After approximately 10 seconds, "PLEASE OPEN LASER BARRIER AND PRESS ANY KEY" will be displayed on the viewfinder. The MENU view will appear. 8 29 Scanning the Object WARNING Never stare into the laser emitting window. Do not place a lens, mirror or optical element in the passage of the laser beam. Doing so may converge the laser beam, resulting in damage to your eyes, burns or fire. [. . . ] Place the object in a position 0. 5 m to 2. 5 m away from the VIVID 910. Insert an initialized memory card into the slot or initialize the current memory card. (It is not possible to initialize a memory card using the VIVID 910. ) Illuminate the object brighter and scan it. Insert a memory card into the slot. Auto-focus failed due to low contrast of the object. [. . . ]