User manual KONICA BIZHUB PRO 1050

[. . . ] Operator Manual Copier POD Administrator Security Table of Contents 1 Safety Information 1. 1 1. 1. 1 1. 1. 2 1. 2 1. 2. 1 1. 2. 2 1. 2. 3 1. 2. 4 1. 2. 5 1. 3 1. 4 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Warning and Precaution Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Meaning of Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Regulation Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Check misalignment (a), in which misalignment occurs if the paper width setting is larger than the actual width, or paper curving (b), in which a sample set is curved if the paper width setting is smaller than the actual width has occurred. a b 6 7 If the desired result cannot be obtained, touch the [ADJUSTMENT] tab. 11x17 - A3 - B4 - 8. 5x14 - A4R - 8. 5x11R - 8. 5x11 - A4 - B5 - A5 5. 5x8. 5 - 8x13 - 8. 125x13. 25 - 8. 5x13 - 8. 25x13 - 8K - 16K - 12x18 A3W - B4W - A4W - A4WR - B5W - A5W - 12x18W - 11x17W 8. 5x11W - 8. 5x11WR - 5. 5x8. 5W - Non-Standard 8 9 Use the touch panel keypad to enter the desired adjustment value, then touch [Set]. Available range: -20 (wide) to +20 (narrow), 1 step = 0. 1 mm Repeat the adjustment steps from 3 to 8 until the desired result is obtained. 13-28 bizhub PRO 1050 Adjustment 13 Touch [Return] to restore the Stapler Position Adjustment Mode Menu Screen. 10 bizhub PRO 1050 13-29 13 13. 10 02 Multi Folder (Punch) Adjustment 13. 10. 101 Paper Width Adjustment Adjustment Perform this adjustment for the specific paper size if punch holes processed by the FD-501 Folding Unit dislocate largely. 13-30 bizhub PRO 1050 Adjustment Procedure 13 Touch [Adjustment] - [02 Finisher Adjustment] - [02 Multi Folder (Punch) Adj. ]. Touch [01 Paper Width Adjustment] to display the Paper Width Adjustment Screen. Load the desired size of paper to be adjusted on a tray, specify the set number to 10, then press [Start]. Check the diameter of penetrated holes when output sheets are piled up. All - 11x17 - A3 - B4 - 8. 5x14 - A4R - 8. 5x11R - B5R - 8. 5x11 - A4 A5R - B5 - A5 - 5. 5x8. 5 - 8x13 - 8. 12x13. 2 - 8. 5x13 - 8. 25x13 - 8K 16K - 16KR - 12x18 1 2 3 4 5 6 7 8 Use the touch panel keypad to enter the desired adjustment value, then touch [Set]. Available range: -20 (wide) to +20 (narrow), 1 step = 0. 1 mm 2 Note If the setting is too wide, the centre position of punch holes may dislocate. If the setting is too narrow, the position of punch holes may vary. 9 10 Repeat the adjustment steps from 3 to 8 until the desired result is obtained. Touch [Return] to restore the Multi Folder (Hole-Punch) Adjustment Mode Menu Screen. bizhub PRO 1050 13-31 13 13. 10. 202 Hole-Punch Vertical Position Adjustment Adjustment Perform this adjustment for the position of punch holes to the direction of paper feed. 13-32 bizhub PRO 1050 Adjustment Procedure 13 Touch [Adjustment] - [02 Finisher Adjustment] - [02 Multi Folder (Punch) Adj. ]. Touch [02 Hole-Punch Vertical Position Adjustment] to display the Hole-Punch Vertical Position Adjustment Screen. Load the desired size of paper to be adjusted on a tray, specify [Punch], then press [Start]. Check the distance (a) from the edge of the feeding sheet to the centre position of the punch hole. a 1 2 3 4 5 6 7 If the desired result cannot be obtained, touch the [ADJUSTMENT] tab. All - 11x17 - A3 - B4 - 8. 5x14 - A4R - 8. 5x11R - B5R - 8. 5x11 - A4 A5R - B5 - A5 - 5. 5x8. 5 - 8x13 - 8. 12x13. 2 - 8. 5x13 - 8. 25x13 - 8K 16K - 16KR - 12x18 8 9 10 Select the desired hole type. Use the touch panel keypad to enter the desired adjustment value, then touch [Set]. Available range: -40 (wide) to +40 (narrow), 1 step = 0. 1 mm Repeat the adjustment steps from 3 to 9 until the desired result is obtained. bizhub PRO 1050 13-33 13 11 12 Adjustment If adjustment in any other hole type or paper size is required, repeat steps from 3 to 10. Touch [Return] to restore the Multi Folder (Hole-Punch) Adjustment Mode Menu Screen. 13-34 bizhub PRO 1050 Adjustment 13 13. 11 03 Multi Folder (Fold) Adjustment 13. 11. 101 Folding Position Adjustment Perform this adjustment for the folding position processed by the FD-501 Folding Unit. bizhub PRO 1050 13-35 13 Procedure Adjustment 1 2 3 4 5 6 7 8 Touch [Adjustment] - [02 Finisher Adjustment] - [03 Multi Folder (Fold) Adj. ]. Touch [01 Folding Position Adjustment] to display the Folding Position Adjustment Screen. Load the desired size of paper to be adjusted on a tray, specify [Folding], then press [Start]. Touching [Next] continuously will change the paper size as follows: All - 11x17 - A3 - B4 - 8. 5x14 - A4R - 8. 5x11R - 8K - 12x18 Use the touch panel keypad to enter the desired adjustment value, then touch [Set]. Available range: -50 to +50, 1 step = 0. 1 mm a Paper feed direction 2 Note When misalignment (a) of step 5 has occurred, enter the "+" value. 9 10 13-36 Repeat the adjustment steps from 3 to 8 until the desired result is obtained. If adjustment in any other size is required, repeat steps 3 to 9. bizhub PRO 1050 Adjustment 13 Touch [Return] to restore the Multi Folder (Fold) Adjustment Mode Menu Screen. 11 bizhub PRO 1050 13-37 13 13. 11. 202 Letter Fold-in Position Adjustment Adjustment Perform this adjustment for the folding positions in Letter Fold-in mode processed by the FD-501 Folding Unit. 2 Reminder When adjusting both Single Fold and Double Fold, be sure to start with the Double Fold adjustment. [. . . ] 13-55 Paper Misfeed . . . . . . . . . . . . . . . . . . . . . . . . 20-8 Paper Presetting . . . . . . . . . . . . . . . . . . . . 5-4 Paper removal button . . 2-14, 4-17 Paper Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Paper size . . . . . . . . . . . . . . . . . . 12-3, 12-16 Paper Tray Setting . . . . . . . . . . . . . . . . . 6-42 Paper type . . . . . . . . . . . . . . . . . . 12-4, 16-18 Paper Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]